32
Basic Operations of the Function Menu
Ch
apt
er 3
P
repa
ra
ti
ons
3-7-2 Function Menu Item List
HOME page
a) The selection of LTC and VITC depends on the setting for TCR on the P4
TC page.
b) Not displayed when TCG is not set to INT and PRST/RGN is not set to
PRESET on the P4 TC page.
P1 PROCS page
Item
Setting
CHARACTR
Specifies whether or not to superimpose
timecodes, menu settings, error
messages, and so on over the video
signals output to the HD SDI OUTPUT
(SUPER) connectors, SDI OUT 2
(SUPER) connector, and COMPOSITE
OUT 2 (SUPER) connector.
ON:
Superimpose.
OFF:
Do not superimpose.
PB/EE
Selects the video and audio signals
output during fast forward, rewind, stop,
and standby.
PB:
Playback signals
EE:
E-E mode signals
CONFI
Selects whether or not to use the
confidential playback function when
recording.
ENABLE:
Use the confidential playback
function.
DISABLE:
Do not use the confidential
playback function.
CTL/TC
Selects the time data to display in time
data display area.
TC:
Playback timecode read by the internal
timecode reader or recording timecode.
The LTC or VITC time data type
indicator is lit.
a)
UB:
User bits data of playback timecodes or
recording timecode. The LUB or VIUB
time data type indicator lights,
depending on whether the timecode is
LTC or VITC.
a)
CTL:
The running time of the tape being
played back or recorded, as calculated
from a count of CTL signals recorded
on the tape. The time is displayed in
Hours:Minutes:Seconds:Frames
format.
ASSEMBLE
Sets assemble edit mode.
ON:
The assemble edit mode is set, and
ASMBL appears in the display
window.
OFF:
The assemble edit mode is
canceled.
TCG SET
When CTL/TC is set to TC, a screen for
setting the initial value of the timecode
generated by the internal timecode
generator appears.
b)
When CTL/TC is set to UB, a screen for
setting the user bit of the timecode
appears.
b)
Submenu
T
/
t
Selects the digit to set data.
–/+
Sets the value.
SET
Stores the set timecode.
EXIT
Terminates the operation, abandoning
any settings not registered.
Item
Setting
VID.PROC
Selects the control method for the internal
digital video processor.
LOCAL:
Change the settings of the internal
digital video processor by using the
function menu.
MENU:
Change the settings of the internal
digital video processor, using the setup
menu.
Note
When controlling the unit with the HKDV-900,
set to MENU.
VIDEO
Sets the HD/SD video signal output level (
−∞
to +3 dB).
PRESET:
Regardless of manually set values,
the video signal is set to the standard
level.
Manual setting:
With the displayed setting
flashing, you can adjust the video signal
output level by rotating the MULTI
CONTROL knob.
CHROMA
Sets the HD/SD chroma signal output level
(
−∞
to +3 dB).
PRESET:
Regardless of manually set values,
the chroma signal is set to the standard
level.
Manual setting:
With the displayed setting
flashing, you can adjust the chroma signal
output level by rotating the MULTI
CONTROL knob.
HUE/
CHRM PHS
Sets the color phase of the HD/SD output
signal.
PRESET:
Regardless of manually set values,
the color phase is set to the standard
value.
Manual setting:
With the displayed setting
flashing, you can adjust the value across
the range ±30° by rotating the MULTI
CONTROL knob.
Item
Setting
