49
Playback
Chapt
er
3
Rec
o
rd
ing and
P
la
y
bac
k
The repeat indicator lights.
3
Press the SET (YES) button to save the new setting
and close the menu.
4
Press the PLAY button.
The unit starts repeat playback from the repeat start
point set in step
1
.
Setting points A and B for repeat
playback
You can set the repeat playback start point (point A) and
end point (point B) by using the current tape position or
inputting timecode values.
To perform repeat playback after setting points A and B,
press the PLAY button. When the DSRM-10 Remote
Control Unit (option) is connected, you can also start
repeat playback by pressing its PLAY button.
When performing repeat playback using points A and B as
the playback start and end points, set the REPEAT TOP
and REPEAT END menu items
to A POINT
and B POINT, respectively.
Setting the current tape position as point A
or B
While holding down the SET (YES) button in the menu
control section, press the
<
/
A
or
,
/
B
button. The
timecode value of the current tape position is set as point
A or B, and a message “A set” or “B set” is displayed for
0.5 second in the time counter display.
Once set, the point A or B timecode value is held in the
non-volatile memory of the unit until changed. It is not lost
when the unit is powered off.
When setting point A or B, you can only use a timecode
value. Even when CNT is selected with the COUNTER
SELECT button, you cannot use a CNT value to set point
A or B.
To check the point A or B timecode value
Press the
<
/
A
or
,
/
B
button in the menu control
section. While the button is held down, the point A or B
timecode value is displayed on the monitor screen and in
the time counter display.
If you hold down the
<
/
A
and
,
/
B
buttons
simultaneously, the value shown is the point B timecode
value minus the point A timecode value. If the point A
timecode value is greater than the point B timecode value,
a minus sign (–) is shown before the value.
Inputting timecode values for points A and
B
Use the following procedure.
You can also use this procedure to finely adjust the
timecode values for points A and B.
1
Press the MENU button.
The SYSTEM MENU display appears.
Note
PRESET
VARIABLE
REC
PB
LEVEL
MONITOR
SELECT
COUNTER
SELECT
PHONES
CONTROL-S
REW
PLAY
F FWD
1
2
3
A
B
4
OVER
CH
1
0
-12
-20
-30
-40
-60
REC
STOP
TC
VITC
44.1K
OVER
REPEAT
1080 525
CH
2
EDIT MODE
REC INHI
EJECT
LOCAL
i.LINK
HDV DVCAM
(DV)
9PIN
01:23:45:15
REC/PB LEVEL
POWER
DISPLAY
MENU
A
B
MENU
RESET(NO)
SET(YES)
TC
PRESET
ASSIGN
RESET(NO)
SET(YES)
TC
PRESET
ASSIGN
CH1 1/2
CH2 3/4
INPUT SELECT
HD VIDEO
SD VIDEO
Buttons used for setting
the current tape position
as point A
Buttons used for setting
the current tape position
as point B
Note
A
B
MENU
RESET(NO)
SET(YES)
TC
PRESET
ASSIGN
5,7,9,12
13
12
8
,11
1,15
2-4,6,
10,11
Setup menu
S Y S T E M M E N U
S E T U P M E N U
A U T O F U N C T I O N
H O U R S M E T E R
Monitor screen
Time counter display
