Timecode/User Bit Recording and HDMI
®
Embedded Timecode Output
The HXR-NX30U features the important professional camcorder functions of timecode and user bit settings. Like other NXCAM camcorders,
the HXR-NX30U’s timecodes can be centrally reset using the supplied infrared remote control to allow easy synchronization of video from
compatible* camera models. Using NLE software, live footage shot with multiple NXCAM camcorders can be efficiently edited with timecode sync.
Timecodes and user bits can also be output through an HDMI jack.
*Compatible Sony NXCAM camcorder models.
Built-in Light
The built-in light functions
as a flash when shooting
still images or as an
auxiliary light source when
recording video. Using the
NightShot
®
mode is
particularly effective when
recording in low-light
conditions and allows you
to capture otherwise
impossible shots.
Built-in Projector
A built-in projector
can project images
up to 100 inches
wide (when
projecting 15 ft from
a screen, 40 inches
wide when
projecting 6ft from a
screen). Large-screen projection of images enables all the staff
involved to check the rushes at the end of the shoot and reduces the
need for an external display.
Built-in USB cable for easy file transfer/charge
The high-speed, built-in USB 2.0 cable allows for easy connection to
your computer for charging or file transfer without having to
remember separate cables. It also fits conveniently into the hand
strap so it’s out of the way until you need it. Charging your
camcorder is faster than ever now through the USB; for every two
minutes of charge time you get up to one minute of recording time.
Geotagging with built-in GPS receiver
A built-in GPS receiver makes the HXR-NX30U an ideal choice for
professional videographers. The receiver gives you the ability to “tag”
your shooting locations as a future reference if you need to return to
the same location or to create a log of areas covered when surveying
remote locations.
Additionally, the receiver automatically adjusts your camcorder’s
clock to the proper time zone when international travel is part of your
assignment. Your locations can be tracked on Google Maps™** and
all GPS data can be extracted with a CMU is supplied PC software.
** Map service requires PC with internet. Service provided by Google and
subject to change without notice.
OPTIONAL ACCESSORIES
Memory Stick PRO-HG Duo™
MS-HX32B
(32 GB, 16 GB, 8 GB)
Wide Conversion Lens
VCL-HGA07B
(0.75x)*
SD / SDHC Memory Card
SF-32UX
(32 GB, 16 GB, 8 GB,)
Tele Conversion Lens
VCL-HG1737C
(1.7x)*
AC Adaptor/Charger
AC-VQV10
(AC 100 V – 240 V)
Battery Charger
BC-TRV
(AC 100 V – 240 V)
Rechargeable Battery Pack
NP-FV70
(6.8 V / 14.0 Wh / 2060 mAh)
NP-FV100
(6.8 V / 26.5 Wh / 3900 mAh)
Accessory Kit
ACC-V1BP
(Include NP-FV100 and AC-VQV10)
Accessory Kit
ACC-VA1BP
(include NP-FV70, BC-TRV, RM-VD1 etc)
*HXR-NX30U cannot output S Video out
* The supplied step-down ring is required to mount conversion lenses. Conversion
lenses cannot be mounted unless the supplied hood is removed. Also, be sure
to set the conversion lens mode on the body before using. When using the Wide
Conversion Lens setting, switch Balanced Optical SteadyShot off.
Direct Copy to external HDD without PC
Back up your footage while you’re in the field, directly from your
camcorder by attaching an optional USB hard disk drive*, without the
need for a computer. Your camcorder can also access videos stored
on the external hard drive for playback on your monitor* allowing you
to utilize the camcorder’s handy playback features.
*Note:
1. Direct Copy is compatible with USB media that meets the following requirements:
• USB media that meets the USB2.0 requirement.
• For external HDD or USB memory under 2TB, an AC powered external HDD is recommended.
• USB media formatted in the FAT32 file system. In the case when USB media is not in
FAT32 file system, reformatting is required and all data will be erased.
Note: There may be cases when USB media is not compatible with the Direct Copy function.
2. When using Direct Copy the camcorder needs to be connected to AC power.
3. Using VMC-UAM1(supplied) cable when the HXR-NX30U is connected to External HDD.
4. Connection via USB-hub is not supported.
