background image

Setting the Clock

1

Plug in the clock radio.

"AM 12:00" will flash in the display.

2

Press 

CLOCK

 for a few seconds.

You will hear a beep and the year will start to
flash in the display.

3

Press  

TUNE/TIME SET +

 or 

 until the

correct year appears in the display.

4

Press 

CLOCK

 once.

5

Repeat steps 

3

 and 

4

 to set the month,

date, hour, and minute.

After setting the minute, press and release

CLOCK

 to start the counting of the seconds.

• To display the year and date, press 

SNOOZE/

DATE/SLEEP OFF

 once for the date and within

2 seconds press it again for the year. The date
or year will appear in the display for a few
seconds and then the display returns to the
current time.
When 

SNOOZE/DATE/SLEEP OFF 

is pressed

while the SNOOZE function is operating, the
year and date will not appear in the display.

• To set the current time rapidly, hold down the

+

 or 

 button.

• To set the current time from zero seconds,

release 

CLOCK

 with the time signal at step 

5

.

To change the display to the
daylight saving time (summer time)
indication

Press 

D.S.T./SUMMER T.

” is displayed and the time indication

changes to summer time.
To cancel the summer time indication, press

D.S.T./SUMMER T.

 again.

Playing the Radio

Manual Tuning

1

Press 

RADIO ON

 to turn on the radio.

The band and frequency will appear in the
display for a few seconds and then the
current time indication returns to the display.

2

Press 

BAND

 repeatedly to select the

desired band.

3

Use 

TUNE/TIME SET +

 or 

 to tune in

the desired station.

The FM frequency advances or reverses in 0.1
MHz channel steps and the AM frequency in
10 kHz channel steps.
A beep sounds when the upper or lower
extremity of the band range is reached.

4

Adjust volume using 

VOLUME

.

• To turn off the radio, press 

RADIO OFF

.

• To improve reception

FM:

Extend the FM wire antenna fully to
increase FM reception sensitivity.

AM:

Rotate the unit horizontally for optimum
reception. A ferrite bar antenna is built in
to the unit.

• To check the current station, press the 

+

 or 

button lightly. The band and frequency are
displayed for a few seconds, after which the
current time indication returns to the display.

• If the radio alarm A RADIO

 

comes on while

the radio is playing, the station switches to the
frequency set under preset number 

1

.

To set the brightness of the
backlight

Set 

BRIGHTNESS

 to 

(high) or 

(low) to make

the display more visible.

Preset Tuning

You can preset up to five stations for one-touch
tuning, one under each of preset buttons 

1

 to 

5

.

Presetting a station

Example: To set AM 1260 kHz in preset

button 

2

.

1

Press 

RADIO ON

 to turn on the radio.

2

Tune in the station you want to preset.

(See “Manual Tuning”)

3

Hold down the desired

STATION•SELECT/PRESET

 button (in

this case, 

2

) until you hear two short

beeps.

The frequency will appear for a few seconds
and then the display will return to the
current time.

• When using the radio alarm, preset the station

you wish to serve as the alarm under preset
button 

1

.

To change a preset station

Press the preset number again after tuning in
manually to a different station. The previous
station is replaced by the new one.

Tuning in a preset station

1

Press 

RADIO ON

 to turn on the radio.

2

Press the 

STATION•SELECT/PRESET

button under which the desired station
is stored.

3

Adjust volume using 

VOLUME

.

After a few seconds, the display will return to
the current time but the preset number
indication will remain.

Using the Digital
Voice Memo

1

Press 

VOICE MEMO•REC

 until you

hear a beep.

2

Speak into the 

MIC

 while “

” flashes

(within 20 seconds).

The recording time displays and starts to
elapse.

3

Press 

VOICE MEMO•REC

 again to

stop the recording.

“End” will appear in the display with a long
beep sound.

4

Press 

VOICE MEMO•PLAY

 to play

back and to confirm the recorded
memo.

Notes

• Only one message can be recorded and up to

about 20 seconds.

• If you want to keep the recorded message, be

careful not press the 

VOICE MEMO•REC

button. Since the recording overlaps the last
recorded message.

• The volume cannot be adjusted for the voice

memo.

Setting the Alarm

You can set the radio and buzzer alarms at the
preset time.  Before setting the alarm, be sure to
set the clock (See “Setting the Clock”) and preset
a radio station under preset button 

1

 (See “Preset

Tuning”).

1

Turn off the radio.

2

Hold down 

A RADIO

 

or

 

B BUZZER

until a short beep sounds.

The “A RADIO”

 

or

 

“B BUZZER” indication

and the hour will flash in the display.

3

Press either 

TUNE/TIME SET +

 or 

until the desired hour appears in the
display.

4

Press 

A RADIO

 

or

 

B BUZZER 

to set the

minute.

The minute will flash in the display.

5

Press either 

TUNE/TIME SET +

 or 

until the desired minute appears in the
display.

6

Press 

A RADIO

 

or

 

B BUZZER

.

Two short beeps sound to indicate successful
presetting.

7

Press 

ALARM MODE

 

repeatedly until

the alarm you want appears in the
display.

Each time you press 

ALARM MODE

, the

alarm indication changes as follows.

and

No alarm
indication

When the alarm time is reached, the radio or
buzzer sounds for 60 minutes or until turned off.

To stop the alarm

Press 

ALARM RESET

 while the alarm is

activated.

The alarm will function at the same time the next
day.

To cancel the alarm

Press 

ALARM MODE

 until neither the

“A RADIO”

 

nor

 

“B BUZZER” indication is

displayed.

Notes

• The alarm does not function, unless you set

the clock, A RADIO

 

and B BUZZER

 

function.

• If both the radio and buzzer alarm are set for

the same time, the radio alarm takes
precedence.

• You can check the alarm time setting by

pressing 

A RADIO

 or 

B BUZZER

.

To doze for a few more
minutes

1

Press 

SNOOZE/DATE/SLEEP OFF

.

The radio or buzzer will shut off but will
automatically come on again after about
8 minutes. You can repeat this process as
many times as you like.

• The alarm indicator flashes continuously

during the snooze function.

To set the Wake Up
Memo

1

Set the alarm mode. (See “Setting the
Alarm”.)

2

Set the voice memo. (See “Using the
Digital Voice Memo”.)

3

Press 

WAKE UP MEMO

.

” will be displayed.

When the alarm time is reached, the voice
memo plays back and then the radio or
buzzer will go on for 60 minutes or until
turned off. When you press 

ALARM RESET

 to

turn off the alarm, the voice memo plays
back and then the alarm mode turns off.
When 

SNOOZE/DATE/SLEEP OFF

 is pressed

during the radio or buzzer alarm with the
wake up memo, the radio or buzzer will shut
off and the voice memo will play back each
time.

Note

The Wake Up Memo operates only with the
alarm function.

Setting the Sleep
Timer

You can enjoy falling asleep to the radio using
the built-in sleep timer that turns off the radio
automatically after a preset duration.

1

Press 

SLEEP

.

The radio turns on. It will go off after the
preset time has passed. You can set the sleep
timer to 90, 60, 30, or 15 minutes. Every push
changes the display as follows.

The radio will play for the time you set, then
shut off.

• To turn off the radio before the preset time,

press 

SNOOZE/DATE/SLEEP OFF

.

To Use Both Sleep Timer
and Alarm

You can fall asleep to the radio sound and you
will
be awakened by the radio or buzzer alarm at the
preset time.

1

Set the alarm. (See “Setting the
Alarm”.)

2

Set the sleep timer. (See “Setting the
Sleep Timer”.)

Troubleshooting

Should any problem occur with the unit, make
the following simple checks to determine
whether or not servicing is required.
If the problem persists, consult the nearest Sony
dealer.

The clock does not show the correct time.

• Has an electrical power outage lasting more

than half an hour occurred?

The radio or buzzer alarm does not sound at
the preset alarm time.

• Has the desired radio and/or buzzer alarm

mode been activated with the 

ALARM MODE

button ("A RADIO" and/or "B BUZZER"
indication shown in the display)?

The Wake Up Memo does not sound at the
preset alarm time.

• Press 

VOICE MEMO•PLAY

 to confirm if a voice

memo is recorded.

• Has the Wake Up Memo mode been activated

(“

” indication shown in the display)?

• Has the desired radio and/or buzzer alarm

mode been activated with the 

ALARM MODE

button ("A RADIO" and/or "B BUZZER"
indication shown in the display)?

OFF (current time)

On

90(min)

30

15

60

AC power cord

MIC

FM wire antenna

BRIGHTNESS

VOLUME

SNOOZE/DATE/SLEEP OFF

D.S.T./SUMMER T.

1

2

3

4

5

RADIO

OFF

RADIO

TUNE / TIME SET

BAND

CLOCK

STATION

SELECT /

PRESET

WAKE UP MEMO

WAKE UP STATION

ALARM RESET

ALARM MODE

SLEEP

A

BUZZER

B

ON

VOICE MEMO•

PLAY

VOICE MEMO•

REC

Reviews: