1-20
VPL-S900E, VPL-S900M, VPL-S900U
38
(EN)
Troubleshooting
If the projector appears to be operating erratically, try to diagnose and correct the problem, using the following
guide. If the problem still persists, consult with qualified Sony personnel.
Symptom
Cause
Remedy
The power is not turned on.
No picture and no sound.
No picture or no sound.
No picture.
The picture is noisy.
When inputting sound through
INPUT A/B connector, sound
comes through one channel only.
The picture from INPUT A/B
connector is colored strange.
“Please check INPUT-A in
SET SETTING.” appears in
spite of inputting the correct
signal from INPUT A.
“Please check INPUT-B in
SET SETTING.” appears in
spite of inputting the correct
signal from INPUT B.
No display appears though
the correct signal is input from
INPUT B.
“NO INPUT” appears when
15k RGB or component signal
is input.
On-screen displays do not
appear.
Color balance is incorrect.
The picture is too dark.
The picture is not clear.
Wait for about one minute before turning on the
power
(see page 22 (EN)).
Close the lamp cover securely.
Close the air filter cover securely
(see page 37 (EN)).
Check that the proper connections have been
made
(see pages 18 (EN) to 21 (EN)).
Check that the proper connections have been
made
(see pages 18 (EN) to 21 (EN)).
Select the input source correctly using the INPUT
key
(see page 22 (EN)).
Press the MUTING keys to release the muting
function
(see page 23 (EN)).
Set the computer signal to output to external
monitor
(see page 18 (EN)).
Set the computer signal to output only to external
monitor
(see page 18 (EN)).
Change the desktop pattern on the connected
computer.
Input stereo sound.
Select RGB or COMPONENT for INPUT-A or
INPUT-B in the SET SETTING menu according to
the input signal
(see page 31 (EN)).
Select RGB or COMPONENT for INPUT-A in the
SET SETTING menu according to the input signal
(see page 31 (EN)).
Select RGB or COMPONENT for INPUT-B in the
SET SETTING menu according to the input signal
(see page 31 (EN)).
Set the switch to IN
(see page 14 (EN)).
Input the correct sync signal (composite sync or
sync on G signal (sync on Y for component
signal)).
Set STATUS in the SET SETTING menu to ON
(see page 31 (EN)).
Adjust the picture
(see pages 26 (EN) and 27 (EN)).
Set COLOR SYS in the PICTURE CTRL menu to
match the color system being input
(see page 27 (EN)).
Adjust the contrast or brightness in the PICTURE
CTRL menu properly
(see page 26 (EN)).
Adjust the focus
(see page 23 (EN)).
Leave the projector for about two hours with the
power on
(see page 35 (EN)).
The power has been turned off and on
with the I /
u
key at a short interval.
The lamp cover is detached.
The air filter cover is detached.
Cable is disconnected.
Wrong connection.
Input selection is incorrect.
Either the picture or the sound is cut off.
The computer signal is not set to output
to external monitor.
The computer signal is set to output to
both the LCD of the computer and
external monitor.
Noise may appear on the background
depending on the combination of the
numbers of dot input from the connector
and numbers of pixel on the LCD panel.
Monaural sound is being input through
the INPUT A/B connector.
Setting for INPUT-A/INPUT-B in the SET
SETTING menu is incorrect.
Setting for INPUT-A in the SET
SETTING menu is incorrect.
Setting for INPUT-B in the SET
SETTING menu is incorrect.
The RGB IN/OUT select switch is set to
OUT.
The sync signal is incorrect.
STATUS in the SET SETTING menu has
been set to OFF.
Picture has not been adjusted properly.
Projector is set to wrong color system.
Contrast or brightness has not been
adjusted properly.
Picture is out of focus.
Condensation has occurred on the lens.
39
(EN)
NO INPUT
Not applicable!
High Temperature!
Power off in 1 min.
Frequency is out of range!
Please check INPUT-A in SET
SETTING.
Please check INPUT-B in SET
SETTING.
Symptom
Cause
Remedy
The LAMP/COVER indicator
flashes.
The LAMP/COVER indicator
lights up.
The TEMP/FAN indicator
flashes.
The TEMP/FAN indicator
lights up.
The Remote Commander
does not work.
The laser pointer is not
emitted.
The joystick, R CLICK, or L
CLICK key does not function.
Warning messages
Use the list below to check the meaning of the messages displayed on the screen.
Message
Meaning
Remedy
Internal temperature is too high.
This input signal cannot be projected as
the frequency is out of the acceptable
range of the projector.
The resolution setting of the output
signal of a computer is too high.
You have input RGB signal from the
computer when INPUT-A in the SET
SETTING menu is set to COMPONENT.
You have input RGB signal from the
computer when INPUT-B in the SET
SETTING menu is set to COMPONENT.
Turn off the power.
Check to see if nothing is blocking the ventilation
holes.
Input a signal that is within the range of the
frequency.
Set the setting of output to the SVGA.
Set INPUT-A correctly.
Set INPUT-B correctly.
Caution messages
Use the list below to check the meaning of the messages displayed on the screen.
Message
Meaning
Remedy
No input signal
You have pressed the wrong key.
Check connections.
Press the appropriate key.
The lamp cover or the air filter cover is
detached.
The lamp has reached the end of its life.
The fan is broken.
The internal temperature is unusually
high.
The Remote Commander batteries are
dead.
The COMMANDER ON/OFF switch is
set to the OFF position.
You are using the Remote Commander
as a wireless Remote Commander, and
it is connected to the projector.
The front/rear remote commander
detector is near the fluorescent lamp.
The batteries are dead.
The Remote Commander is used as
wired without batteries.
The mouse port on the computer does
not recognize the mouse cable.
Attach the cover securely
(see page 37 (EN)).
Replace the lamp
(see page 37 (EN)).
Consult with qualified Sony personnel.
Check to see if nothing is blocking the ventilation
holes.
Replace with new batteries
(see page 16 (EN)).
Set the switch to ON position
(see page 16 (EN)).
Disconnect the cable.
Change the setting of SIRCS RECEIVER in the
SET SETTING menu
(see page 32 (EN)).
Replace with new batteries
(see page 16 (EN)).
Install batteries
(see page 16 (EN)).
Restart the computer.
Summary of Contents for IFB-X600E
