10
System Requirements
Chapt
er 1 In
tro
duc
tion
H
Audio input connector (Used for future expansion)
Use this connector to input audio from a peripheral
audio device, such as a microphone.
Plug-In Power microphones are supported.
I
Mini-SAS output connector
Use this connector to connect the mini-SAS cable used
for connecting an NSRE-S200.
The NSRE-S200 is an optional expansion storage unit.
J
USB connector
Use this connector to connect a USB keyboard, USB
mouse, USB flash memory, or System Controller
(RM-NS1000) to the NSR.
K
LAN connectors (1 to 4)
Use these connectors to connect 10 Base-T, 100 Base-
TX, or 1000 Base-T network cables.
LAN1:
Network cameras
1)
LAN2:
Network cameras
1)
(LAN2 can only be used
when using a different segment from LAN1.)
1) Connect remote clients to the network specified with the [Network
Interface for Remote Client] setting (either LAN1 or LAN2) in the
Server Configuration screen. For details on the Server
Configuration screen, see
“Configuring Settings Related to
.
LAN3:
Used for iSCSI storages
2)
LAN4:
Used for iSCSI storages
2)
2) For details on using iSCSI storage, contact your Sony dealer.
L
Monitor connectors (1 and 2)
Use these connectors to connect a monitor.
Monitor connector 1 (and monitor connector 1 on the
front of the unit) and
H
HDMI monitor connector 1
cannot be used at the same time, while monitor
connector 2 and
H
HDMI monitor connector 2 cannot
be used at the same time.
M
Audio output connectors (L and R)
Use these connectors to output audio to a peripheral
audio device.
N
Power supply connector
Use this connector to connect the power cord.
O
Analog camera cable input connector
Use this connector to connect analog cameras via the
analog camera input cable.
The NSR-1050H is standard equipped with this
connector, but the NSR-1200/1100 requires an NSBK-
A16 (optional) expansion.
System Requirements
The hardware required in order to use this recorder are as
follows.
• Network cameras
Contact your dealer for details about compatible
network cameras.
• Monitor
1)
• USB keyboard
2)
• USB mouse
3)
• USB remote controller
4)
• Network switch
• 1000Base-T/100Base-TX/10Base-T cable
• USB memory device
5)
1) This unit supports HDMI-compatible devices and computer
displays that support RGB input.
The following resolutions can be specified.
- Full High-Definition (1,920 × 1,080)
- WUXGA (1,920 × 1,200)
- Full Wide XGA (1,360 × 768)
- UXGA (1,600 × 1,200)
- SXGA (1,280 × 1,024)
- XGA (1,024 × 768)
2) Use a USB keyboard with a cable. However, keys other than
the standard may not function. Wireless or infrared USB
keyboards may also not function properly.
3) Use a USB mouse with a cable. However, three-button or
wheel mice may not function properly. Wireless or infrared
USB mice may also not function properly.
4) You can use a remote controller to control pan, tilt, and zoom
operations for cameras.
- This unit supports RM-NS1000 System Controller and IP
Desktop USB controllers from CH Products. Other remote
controllers are not supported. Do not connect more than one
remote controller.
5) Required when backing up system information such as logs.
- This unit supports standard USB 2.0 Mass Storage devices.
Depending on the type of USB 2.0 Mass Storage device,
however, errors may occur when writing data to the device.
If errors occur when writing data, use a USB memory
device of a different type.
Summary of Contents for Ipela NSR-1050H
Page 138: ......
