TVP-21
74
4. Protection Circuits
Clear unit ventilation areas
and and confirm adequate
local room temperature
Check the following items:
•
The TV should not be located too close any heating elements.
•
The TV should be at least 4 inches
from all walls and enclosures
to ensure adequate ventilation.
•
Check the vented areas on the
lower rear back cover
and the
two rear exhaust fan’s
are clear of all dust and debris.
If all ventilation areas and fans are clear and the TV still shutsdown (2X)
then the next step is to determine if one of the LM75 temperature detection
IC’s on the S1, S2, or C boards have failed. It is a process of elimination
to determine which LM75 has failure.
As the flowchart illustrate start with the least expensive boards and work
your way up.
Substitute new or known good boards in the following order.
Replace
S1 & S2 Boards
(S1) A-1123-098-A
(S2) A-1123-099-A
Replace
Optical Block
50" A-1148-155-A
60" A-1127-174-A
1) S1-Board
2) S2-Board
NOTE: The S2-Board is mounted in difficult-to-get-to spot. Therefore,
the best way to substitute for the board, with very little disassembly,
is to have a extra wire harness (between S-Board and Main Wire
Harness) to connect the substitute board at the interconnect jack.
3) Optical Block (C-Board)
If the TV still shuts down (2X) after the previous substitutions then there
is a problem with the DE microprocessor, consequently, the ASU/DSU
assembly must be replaced.
Replace
ASU/DSU Assembly
50" A-1152-715-A
60" A-1152-714-A
Lamp Cover/Plug Error (3X)
3X Flash
Pattern
(Lamp Cover & Plug)
Two situations can cause the 3X flash pattern.
1) A problem with the
lamp door
positioning and closing of the door
detector switch
(T1-Board)
2) A problem with the positioning of the lamp and
lamp power plug
and the closing of the power plug detector switch
(T3-Board)
The first step befire replacing any parts is to check for proper positioning
of the lamp door and power plug. Furthermore, check for damage to the
following items.
Check
T1 & T3 Boards
Lamp-Door
Switch & Lamp
Connector
Switch
Check
Lamp
&
Lamp Door
is
securely seated
& undamaged
Summary of Contents for KDS-R60XBR1 - 60" Rear Projection TV
