Model name1[KP-46WT510] Model name2[KP-51WS510] Model name3[KP-57WS510] Model name4[KP-65WS510]
[4-094-605-12]
2
Model name1[KP-46WT510] Model name2[KP-51WS510] Model name3[KP-57WS510] Model name4[KP-65WS510]
[4-094-605-12]
❑
Reorient or relocate the receiving antenna.
❑
Increase the separation between the equipment and
receiver.
❑
Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
❑
Consult the dealer or an experienced radio/TV
technician for help.
CAUTION
How to reduce the risk of “Image
Retention” on your Projection TV
Bright, stationary images such as TV station logos
displayed on your TV can cause permanent damage to
your TV, resulting in retention of the image in the picture.
Please take the following steps to reduce the risk of
causing image retention:
View a variety of program sources or programming
material.
Image retention can occur when bright stationary images
such as TV station logos are viewed. Changing the
program material viewed reduces the possibility that a
single image will become imprinted on the picture tubes
in your TV.
When viewing programs with stationary images, adjust
the picture setting to reduce the “Picture” and
“Brightness” levels. Image retention is accelerated by
higher “Brightness” and higher “Picture” settings.
Please refer to your instruction manual for instructions on
adjusting picture settings.
This will help you reduce the risk of causing image
retention.
IMAGE RETENTION IS NOT COVERED BY
YOUR WARRANTY
This document is for the remote control RM-Y909.
MODELS: KP-46WT510, KP-51WS510, KP-57WS510,
and KP-65WS510.
Please keep this notice with the instruction manual.
Safety
❑
Operate the projection TV only on 120 V AC.
❑
The plug is designed, for safety purposes, to fit into
the wall outlet only one way. If you are unable to
insert the plug fully into the outlet, contact your
dealer.
❑
If any liquid or solid object should fall inside the
cabinet, unplug the projection TV immediately and
have it checked by qualified service personnel
before operating it further.
❑
If you will not be using the projection TV for several
days, disconnect the power by pulling the plug itself.
Never pull on the cord.
For details concerning safety precautions, see
“IMPORTANT SAFEGUARDS” on page 3.
Installing
❑
To prevent internal heat buildup, do not block the
ventilation openings.
❑
Do not install the projection TV in a hot or humid
place, or in a place subject to excessive dust or
mechanical vibration.
❑
Avoid operating the projection TV at temperatures
below 5°C (41°F).
❑
If the projection TV is transported directly from a
cold to a warm location, or if the room temperature
changes suddenly, the picture may be blurred or
show poor color due to moisture condensation. In
this case, please wait a few hours to let the moisture
evaporate before turning on the projection TV.
❑
To obtain the best picture, do not expose the screen
to direct illumination or direct sunlight. It is
recommended to use spot lighting directed down
from the ceiling or to cover the windows that face
the screen with opaque drapery. It is desirable to
install the projection TV in a room where the floor
and walls are not of a reflective material.
Trademark Information
TruSurround, SRS and
symbol are trademarks of
SRS Labs, Inc. TruSurround technology is incorporated
under license from SRS Labs, Inc.
BBE and BBE Symbol are trademarks of BBE Sound,
Inc. and are licensed by BBE Sound, Inc. under U.S.
Patent No. 4,638,258 and 4,482,866.
Steady Sound, Digital Reality Creation, Caption
Vision, CineMotion, Memory Stick, and Twin View
are registered trademarks of Sony Corporation.
ClearEdge VM and HD Detailer are trademarks of
Sony Corporation.
You are cautioned that any changes or
modifications not expressly approved in
this manual could void your warranty and
your authority to operate this equipment.
As an ENERGY STAR
®
Partner,
Sony Corporation has determined
that this product meets the
ENERGY STAR
®
guidelines for
energy efficiency.
