Sony LMD-152C, Operating Instructions Manual

2

Owner’s Record

The model and serial numbers are located at the rear. 
Record these number in the space provided below.
Refer to these numbers whenever you call upon your 
Sony dealer regarding this product.

Model No. ____________________
Serial No. ____________________

WARNING

To prevent fire or shock hazard, do not expose the unit to 
rain or moisture.

Dangerously high voltages are present inside the unit. 
Do not open the cabinet. Refer servicing to qualified 
personnel only.

WARNING (for LMD-322WC only)

THIS APPARATUS MUST BE EARTHED.

In the event of a malfunction or when maintenance is 
necessary, consult an authorized Sony dealer. 

This unit contains substances which can pollute the 
environment if disposed carelessly. Please contact our 
nearest representative office or your local environmental 
office in case of disposal of this unit.

For the customers in Europe

This product with the CE marking complies with the 
EMC Directive (89/336/EEC) and the Low Voltage 
Directive (73/23/EEC) issued by the Commission of the 
European Community.
Compliance with these directives implies conformity to 
the following European standards:
• EN60950: Product Safety
• EN55103-1: Electromagnetic Interference (Emission)
• EN55103-2: Electromagnetic Susceptibility 

(Immunity)

This product is intended for use in the following 
Electromagnetic Environment(s):
E4 (controlled EMC environment, ex. TV studio).

For the Customers in the USA

This equipment has been tested and found to comply 
with the limits for a Class A digital device, pursuant to 
Part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful 
interference when the equipment is operated in a 
commercial environment. This equipment generates, 
uses, and can radiate radio frequency energy and, if not 
installed and used in accordance with the instruction 
manual, may cause harmful interference to radio 
communications. Operation of this equipment in a 
residential area is likely to cause harmful interference in 
which case the user will be required to correct the 
interference at his own expense.

You are cautioned that any changes or modifications not 
expressly approved in this manual could void your 
authority to operate this equipment.

The shielded interface cable recommended in this 
manual must be used with this equipment in order to 
comply with the limits for a digital device pursuant to 
Subpart B of Part 15 of FCC Rules.

This device complies with Part 15 of the FCC Rules.  
Operation is subject to the following two conditions: (1) 
This device may not cause harmful interference, and (2) 
this device must accept any interference received, 
including interference that may cause undesired 
operation.

For the customers in Canada

This Class A digital apparatus complies with Canadian 
ICES-003.

Pour les utilisateurs au Canada

Cet appareil numérique de la classe A est conforme à la 
norme NMB-003 du Canada.

This product contains mercury.  Disposal of this product 
may be regulated if sold in the United States.  For 
disposal or recycling information, please contact your 
local authorities or the Electronics Industries Alliance 
(http://www.eiae.org).

Attention-when the product is installed in Rack 
(for LMD-152C/172WC/212C):  

1.Prevention against overloading of branch circuit: 
When this product is installed in a rack and is supplied 
power from an outlet on the rack, please make sure that 
the rack does not overload the supply circuit.  

2.Providing protective earth:
When this product is installed in a rack and is supplied 
power from an outlet on the rack, please confirm that the 
outlet is provided with a suitable protective earth 
connection.  

3.Internal air ambient temperature of the rack: 
When this product is installed in a rack, please make 
sure that the internal air ambient temperature of the rack 
is within the specified limit of this product.  

4.Prevention against achieving hazardous condition due 
to uneven mechanical loading: 
When this product is installed in a rack, please make 
sure that the rack does not achieve hazardous condition 
due to uneven mechanical loading.  

5.Install the equipment while taking the operating 
temperature of the equipment into consideration: 
Please ensure the amount of air flow required for safe 
operation of this product. For the operating temperature 
of the equipment, refer to the specifications of the 
Operation Manual.