Adjustment Using the Menus
62
USER CONFIG menu
The USER CONFIG menu is used for setting the
system, marker, T/C display, WFM/ALM/VECTOR,
focus, function button, closed caption, and audio.
SYSTEM SETTING
AUTO CHROMA/
PHASE
Adjusts color intensity (CHROMA)
and tones (PHASE).
•
AUTO ADJ VALUE
: Selects
ON or OFF of the auto
adjustment. When you set to
OFF, this parameter is reset
to the factory setting. When
you set to ON, the
automatically adjusted value
is enabled.
•
START
: The auto adjustment
starts when you display the
color bar signals (Full/
SMPTE/EIA) on the screen
and press the menu selection
control. After adjusting the
color intensity, press the
MENU button to clear the
adjustment screen. After the
adjustment is done correctly,
the AUTO ADJ VALUE is
automatically set to ON.
PICTURE CONTROL
Adjusts the picture.
•
ACC (Auto Color Control)
:
Sets ACC circuit on or off.
To check the fine
adjustment, select OFF.
Normally select ON.
•
CTI (Chroma Transient
Improvement)
: When a low
color resolution signal is
input, a crisp image can be
displayed. When the setting
is higher, the picture
becomes even more crisp.
•
V SHARPNESS
: A crisp image
can be displayed. When the
setting is higher, the picture
becomes even more crisp.
INPUT SETTING
•
SHIFT H
: Adjusts the position of
the picture. As the setting
increases, the picture moves
to the right, and as the
setting decreases, the picture
moves to the left.
•
SHIFT V
: Adjusts the position of
the picture. As the setting
increases, the picture moves
up, and as the setting
decreases, the picture moves
down.
Submenu
Setting
Submenu
Setting
NTSC SETUP
Selects the NTSC setup level from
two modes.
The 7.5 setup level is used mainly
in North America. The 0 setup level
is used mainly in Japan.
FORMAT DISPLAY
Selects the display mode of the
signal format and scan mode.
•
ON
: The format and scan mode
are always displayed.
•
OFF
: The display is hidden.
•
AUTO
: The format and scan
mode are displayed for
about 5 seconds when the
input of the signal starts.
LANGUAGE
Selects the menu or message
language from among seven
languages.
•
ENGLISH
: English
•
FRANÇAIS
: French
•
DEUTSCH
: German
•
ESPAÑOL
: Spanish
•
ITALIANO
: Italian
•
: Japanese
•
: Chinese
POWER SAVING
Sets the power saving mode on or
off. When you set to ON, the
monitor goes into power saving
mode if no signal is input for about
one minute.
S Y S T E M S E T T I N G :
M A R K E R S E T T I N G :
T / C D I S P L AY S E T T I N G :
I M D S E T T I N G :
W F M / A L M / V E C T O R S E T T I N G :
F O C U S S E T T I N G :
F U N C T I O N B U T T O N S E T T I N G :
C L O S E D C A P T I O N S E T T I N G :
A U D I O S E T T I N G :
USER CONFIG
N T S C S E T U P :
xxxxx
x
F O R M AT D I S P L AY:
xx
xxxx
L A N G U A G E :
E N G L I S H
P O W E R S AV I N G :
xxx
xxx
I / P M O D E :
xxxxxxx
L E D B R I G H T N E S S :
xxxxx
x
R G B R A N G E :
xxxxxx
S D P I X E L M A P P I N G :
xxxxxxx
USER CONFIG – SYSTEM SETTING
