Rec
o
rd
ing to
M
D
s
lename[C:\Documents and Settings\pc13\Desktop\MDS-JE480 PMRF\Revise
Model\J9060101_4238553151MDSJE480CEL\4238553151\GB05OPE-CEL.fm]
model name1[MDS-JE480]
[4-238-553-
15
(1)]
masterpage:Left
(3 column)
9
GB
To prevent accidental erasure of the
recorded material
To protect an MD recording, slide the record-
protect tab in the direction of the arrow (see
illustration below) to open the slot. To enable
re-recording, close the slot.
Recording for long times
This deck has two long time recording modes:
LP2 and LP4 (MDLP recording). When
recording in LP2 Stereo mode, you can record 2
times the normal recordable time, and in LP4
Stereo mode, you can record 4 times the normal
recordable time. In addition, the recordable
time for monaural recording is approximately
double the stereo recording time.
LP4 Stereo mode (4
×
long time recording
mode) achieves a long stereo recording time by
using a special compression system. When
placing emphasis on sound quality, Stereo
recording or LP2 Stereo recording (2
×
long
time recording mode) is recommended.
1
Do steps 1 to 4 of “Recording to an MD”
on page 8.
2
Press REC MODE repeatedly to select
the recording mode.
3
Do steps 5 to 8 of “Recording to an MD”
on page 8.
Tips
•
The MDLP indicator lights up when you select LP2
or LP4 in step 2 above.
•
The deck is factory set to add “LP:” at the beginning
of a track name automatically. This indication is
displayed when the track is played on a deck that
does not support long-time recording.
To turn off this function, do the following procedure.
1
While the deck is stopped, playing, or
paused, press MENU/NO.
2
Turn AMS (or press
./>
repeatedly)
until “Setup?” appears, then press PUSH
ENTER or YES.
3
Turn AMS (or press
./>
repeatedly)
until “LPstamp On” (factory setting)
appears, then press PUSH ENTER or
YES.
4
Turn AMS (or press
./>
repeatedly)
to select “LPstamp Off”, and then press
PUSH ENTER or YES.
5
Press MENU/NO.
To add “LP:” automatically again, select “LPstamp
On” in step 4 above.
Notes
•
The recorded “LP:” is a stamp which appears to
indicate that the track cannot be played back when
you try to play the track on a system that does not
support MDLP mode. It does not appear for systems
that support MDLP mode.
•
When set to “On”, “LP:” is recorded as the track
name, so the number of characters that can be input
to an MD is reduced. If you divide an “LP:” track
using the Divide function, “LP:” is also added to the
latter track.
•
The selected recording mode is kept even after
recording is completed, so be sure to check the
recording mode before recording.
•
Tracks recorded in MDLP (LP2 or LP4) Stereo
mode cannot be played back on a system that does
not support MDLP mode.
•
Even if you press REC MODE during recording,
you cannot change the recording mode.
•
Even if you press REC MODE repeatedly to select
MONO, the monitor signal during recording does
not become monaural.
•
You cannot use S.F Edit and some MD edit
functions for tracks recorded in MDLP mode.
Recording tips
— Recording for long times/Marking
track numbers/Smart Space/Adjusting
the recording level/Checking the
remaining recordable time/Input
monitor
To record in
Set REC MODE to
Stereo
Blank (No indicator)
LP2 Stereo
LP2
LP4 Stereo
LP4
Monaural
MONO
Record-protect tab
Slide in the direction
of arrow
continued
Summary of Contents for MDS-JE480
Page 31: ......
