53
MDX-M690
•
SERVO BOARD IC501 CXP84340-231Q (MD MECHANISM CONTROLLER)
Pin No.
Pin Name
I/O
Description
1 to 5
TIN3 to TIN7
I/O
Input of the 4
×
8 matrix test keys (“L” is always output, except in test mode) Not used (open)
6
LOAD
O
Loading motor control signal output to the motor driver (IC305) “H” active *1
7
EJECT
O
Loading motor control signal output to the motor driver (IC305) “H” active *1
8, 9
—
O
Not used (open)
10
MDMON
O
Power supply on/off control signal output of the power controller (IC101) “H”: power on
11
E-SW
I
Inputs a disc loading completion detect switch detection signal
“L”: When completed of a disc loading operation
12
AG-OK
O
Output of aging status in test mode “L”: under aging, “H”: aging completed Not used (open)
13
ADJ-OK
O
Output of status when aging completed in test mode “L”: aging NG, “H”: aging OK
Not used (open)
14 to 17
—
O
Not used (open)
18
DFCTSEL
I
Select whether defect function is used for the CXD2662R (IC301)
“L”: used this function , “H”: not used this function (fixed at “H” in this set)
19
DPLLSEL
I
Select whether double PLL function is used for the CXD2662R (IC301)
“L”: used this function , “H”: not used this function (fixed at “H” in this set)
20
EMPHSEL
I
Select whether emphasis signal output from pin or unilink data
“L”: outputs from both pin and unilink data, “H”: output from pin only (fixed at “H” in this set)
21
LOCK
O
Mini-disc lock detection signal output to the system controller (IC501)
22
—
O
Not used (open)
23
2M/4M
I
Select whether D-RAM capacitance 2M bit or 4M bit “L”: 4M bit (external D-RAM) , “H”: 2M
bit (internal D-RAM of CXD2652AR) (fixed at “L” in this set)
24, 25
—
O
Not used (open)
26
MNT0
I
Focus OK signal input from the CXD2662R (IC301)
“H” is input when focus is on (“L”: NG)
27
MNT1
I
Track jump detection signal input from the CXD2662R (IC301)
28
MNT2
I
Busy monitor signal input from the CXD2662R (IC301)
29
MNT3
I
Spindle servo lock status monitor signal input from the CXD2662R (IC301)
30
RESET
I
System reset signal input from the system controller (IC501) and reset signal generator (IC502)
“L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
31
EXTAL
I
Main system clock input terminal (10 MHz)
32
XTAL
O
Main system clock output terminal (10 MHz)
33
VSS
—
Ground terminal
34
TX
O
Sub system clock output terminal (32.768 kHz) Not used (open)
35
TEX
I
Sub system clock input terminal (32.768 kHz) Not used (fixed at “L”)
36
AVSS
—
Ground terminal (for A/D converter)
37
AVREF
I
Reference voltage input terminal (+5V) (for A/D converter)
38
INIT
I
Initial reset signal input terminal (A/D input) (fixed at “H”)
39
TEMP
I
Temperature sensor (TH501) input terminal (A/D input)
40
ACNT
I
Select the number of load/eject aging times (A/D input)
0h – 54h (30 times), 55h – 0A9h (20 times), 0AAh – 0FFh (10 times)
41
DO-SEL
I
Select the digital output bits (A/D input)
42
EE-CS
O
Chip select signal output to the external EEPROM device Not used (open)
43
EE-CKO
O
Serial data transfer clock signal output to the external EEPROM device Not used (open)
44
EE-SIO
I/O
Two way data bus with the external EEPROM device Not used (open)
45
MD-SO
O
Writing serial data signal output to the CXD2662R (IC301) and CXA2523AR (IC302)
Summary of Contents for MDX-M690
Page 79: ...79 MDX M690 MEMO ...
