54
MDX-M690
Pin No.
Pin Name
I/O
Description
46
LINKOFF
O
Unilink on/off control signal output for the SONY bus “H”: link off Not used (open)
47
UNIREQ
O
Data request signal output terminal (for SONY bus) “H”: request on Not used (open)
48
UNICKIO
I/O
Serial clock signal input from the system controller (IC501) or serial clock signal output to the
system controller (IC501) and SONY bus interface (IC601)
49
UNISI
I
Serial data input from the SONY bus interface (IC601)
50
UNISO
O
Serial data output to the SONY bus interface (IC601)
51
MD-CKO
O
Serial data transfer clock signal output to the CXD2662R (IC301) and CXA2523AR (IC302)
52
MD-SI
I
Reading serial data signal input from the CXD2662R (IC301)
53
—
O
Not used (open)
54
SENS
I
Internal status (SENSE) input from the CXD2662R (IC301)
55
CC-XINT
I
Interrupt status input from the CXD2662R (IC301)
56
LIMIT-IN
I
Detection input from the sled limit-in detect switch
The optical pick-up is inner position when “L”
57
EJT-OK
I
Front panel open detection signal input from the system controller (IC501)
“L”: eject possible
58
ERROR-PWM
O
PWM error monitor output terminal (C1and ATER is output when test mode) Not used (open)
59
MD-RST
O
Reset signal output to the PCM1718E (IC101), CXD2662R (IC301) and BH6518FS (IC303)
“L”: reset
60
BU-IN
I
Battery detect signal input from the SONY bus interface (IC601) and battery check circuit
“H”: battery on
61
BUS-ON
I
SONY bus on/off control signal input from the system controller (IC501) “L”: bus on
62
SQSY
I
Subcode Q sync (SCOR) input from the CXD2662R (IC301)
“L” is input every 13.3 msec Almost all, “H” is input
63
C-SW
I
Inputs a disc loading start or a disc eject completion detect switch detection signal
“L”: When loading start or eject completed of a disc loading operation
64
MD-LAT
O
Serial data latch pulse signal output to the CXD2662R (IC301) and CXA2523AR (IC302)
65
MD-ON
O
Power supply on/off control signal output of the MD mechanism deck section main power supply
“H”: power on
66
DEEMP
O
De-emphasis on/off control signal output to the PCM1718E (IC101) “H”: de-emphasis on
67
A-MUTE
O
Power amplifier muting on/off control signal output to the power amplifier (IC309) and audio line
muting on/off control signal output “H”: muting on
68
—
O
Not used (open)
69
TSTCKO
O
Output of clock signal for the test mode display Not used (open)
70
TSTSO
O
Output of data for the test mode display Not used (open)
71
TSTMOD
I
Setting terminal for the test mode “L”: test mode, “H”: normal mode
72
VCC
—
Power supply terminal (+5V)
73
NC
I
Not used (fixed at “H”)
74 to 77
TOUT0 to TOUT3
O
Output of the 4
×
8 matrix test keys Not used (open)
78 to 80
TIN0 to TIN2
I/O
Input of the 4
×
8 matrix test keys (“L” is always output, except in test mode) Not used (open)
*1 Loading motor (M903) control
LOAD (pin
6
)
“H”
“L”
“H”
“L”
EJECT (pin
7
)
“L”
“H”
“H”
“L”
Terminal
Operation
IN
OUT
BRAKE
STOP
Summary of Contents for MDX-M690
Page 79: ...79 MDX M690 MEMO ...
