Ch
ap
te
r
6
A
d
v
a
nc
ed
O
p
er
at
io
ns
121
Frame Memory
Note
In the following signal formats, a field freeze is not
possible.
1080PsF/23.976, 1080PsF/24, 1080PsF/25, 1080PsF/
29.97, 720P/59.94
This freezes the input image.
In this state, no freeze image has yet been saved. You
can repeat this operation any number of times, until the
desired freeze image is obtained.
8
When you have obtained the freeze image you want,
press [Store] in the Freeze menu, and confirm the
name in the keyboard window.
For details of the saved file names, see the next item,
“File names.”
If, before saving the freeze image, you press [FM
Output] to switch the frame memory, the freeze image
is saved automatically in freeze memory. (Automatic
save)
The freeze image is saved in memory, and a thumbnail
for the video and/or key appears.
The “Remain” count under [Store], showing the
number of images that can be saved, decreases by one
(or by two if [Pair] is turned on in step
3
).
Note
Saved freeze images are erased if you power off the
switcher, or execute a reset with the setup menu. Freeze
images which you do not want to erase must be saved as
files to the hard disk or a “Memory Stick”.
(See Chapter 7
“File Operations” (page 137).)
File names
• When you press [Store], a keyboard window appears,
and the default file name, such as “image001” appears.
To change this, enter the file name in the keyboard
window. (Maximum eight alphanumeric characters)
• For automatic saving, the file name is automatically set
to “auto_000,” “auto_001,” and so on.
• For a key file, “(k)” is automatically appended to the file
name.
Saving files with [Pair] on/off
When saving with [Pair] turned off, a file is created for
either the video or key. (Referred to below as an “Single
file.”)
When [Pair] is turned on, both video and key files are
created with the same name. (Referred to below as “Pair
files.”)
To apply a box-shaped mask to a freeze image
1
To link the video and key with a mask, press [Mask
Link] in the Freeze menu, turning it on.
2
When [Mask Link] is turned off in step
1
, press one of
the output buttons ([FM1V] or [FM1K] in the example
display of the Freeze menu on page 120), to select it.
The selected button turns light blue.
Note
Even when [Pair] is on, if [Mask Link] is off, you can
apply different masks to the video and key. In this
case, press the output button to select it for the
operation.
3
Press [Box Mask], turning it on.
4
Set the parameters for the four sides of the box.
(If you turned [Mask Link] on in step
1
, the parameters
for video side are shown.)
To select frame memory output
1
Press [FM Output].
A popup window appears.
2
Press one of the following.
FM1 V/K:
Frame memory 1 video and key
FM2 V/K:
Frame memory 2 video and key
FM3 V/K:
Frame memory 3 video and key
Number of images which can be
saved / maximum number of images
Knob
Description
Setting values
1 (Left)
Left edge position
–100.00 to +100.00
2 (Right)
Right edge position
–100.00 to +100.00
3 (Top)
Top edge position
–100.00 to +100.00
4 (Bottom)
Bottom edge position –100.00 to +100.00
Summary of Contents for MFS-2000
Page 6: ...6 Table of Contents ...
Page 136: ...Chapter 6 Advanced Operations 136 Copying ...
Page 192: ...192 Other Settings Chapter 9 System Settings ...
Page 198: ...198 Index Index ...
