56
Recording Video Signals from External Equipment (When Using an MSDW-904)
Chapt
er
3
Re
c
o
rdin
g and Pl
a
y
b
a
c
k
2
Turn the MENU knob to move the
b
mark to
“OPERATION.”
3
Press the MENU knob.
If this is the first time the OPERATION menu has been
displayed, the CONTENTS page of the OPERATION
menu appears. If the menu has been used before, the
last accessed page appears.
4
If the CONTENTS page is displayed, turn the MENU
knob to move the
b
mark to “SOURCE SEL,” and
press the MENU knob.
If a different page is displayed, turn the MENU knob
until the SOURCE SEL page appears, then press the
MENU knob to select the page.
SOURCE SEL page
(“SETUP REMOVE” is displayed only when “UC/J SELECT” on the
FORMAT page is set to “J” on the MSW-970.)
5
Turn the MENU knob to move the
b
mark to “REC
VIDEO SOURCE,” then press the MENU knob.
The
b
mark on the left of “REC VIDEO SOURCE”
changes to a
z
mark and the
z
mark on the left of the
setting changes to a ? mark.
6
Turn the MENU knob to display “EXT.”
7
Press the MENU knob.
The
z
mark on the left of “REC VIDEO SOURCE”
returns to a
b
mark and the ? mark on the left of the
setting returns to a
z
mark.
8
To end menu operations, set the MENU ON/OFF
switch to OFF.
The menu disappears from the viewfinder screen, and
the display indicating the current status of the
camcorder appears along the top and bottom of the
screen.
While recording in EXT mode, EXT is displayed
along the top of the viewfinder screen.
• Even when EXT is selected for REC VIDEO SOURCE,
if the external video signal is not input to the GENLOCK
IN connector, the camcorder does not change to EXT
mode, and the pictures being shot by the camcorder are
recorded on the tape.
• Even if GENLOCK ON/OFF is set to OFF on the
GENLOCK page of the MAINTENANCE menu, the
camcorder is automatically synchronized with the
external reference video signal when the external video
signal is input to the GENLOCK IN connector in EXT
mode. When the setting is switched to CAM mode, or
when no signals are input to the GENLOCK IN
connector even in EXT mode, the camcorder is reset to
the original setting.
Selecting the delay mode of the vertical
synchronizing (V sync) signal of the output
video signal
In EXT mode, the video signal output from the TEST OUT
connector or the VIDEO OUT connector is output with a
delay of 8 horizontal lines against the external input signal,
because the input signals, including the V sync signal,
undergo digital processing internally.
There will not be any problems when you see the pictures
of the output video signals on the monitor. However, if you
want to output the V sync signals that are at the same
position as the V sync signals of the external signal, use the
menu to select the appropriate V sync delay.
1
Follow steps
1
to
4
in
“Selecting the signals to be
recorded” (page 55)
until the SOURCE SEL page of
Item
Description
CAM
Records the pictures being shot by the
camcorder.
EXT
Records video signals from the
external equipment connected to the
GENLOCK IN connector (with MSDW-
904).
21 SOURCE SEL TOP
REC VIDEO SOURCE: CAM
EXT OUTPUT DELAY: SYNC
SETUP REMOVE : 7.5%
21 SOURCE SEL TOP
REC VIDEO SOURCE: CAM
EXT OUTPUT DELAY: SYNC
SETUP REMOVE : 7.5%
Notes
21 SOURCE SEL TOP
REC VIDEO SOURCE: EXT
EXT OUTPUT DELAY: SYNC
SETUP REMOVE : 7.5%
Summary of Contents for MSV-970
Page 5: ...5 ...
Page 168: ...168 Index Index ...
Page 170: ...Sony Corporation MSW 970 970P SY 3 863 920 03 1 Printed in Japan 2006 11 13 2005 ...