85
Status Display on the Viewfinder Screen
Chap
te
r 5
Men
u
Dis
p
la
ys
a
nd Det
a
iled
S
e
ttin
gs
VF DISP 2 page
1) When an Anton Bauer Intelligent Battery System or the BP-GL65/
GL95/L60S battery pack is used, the setting of this item determines
the display as follows:
INT:
The remaining battery capacity is shown as a percentage when
there is a change, and when the capacity is low.
AUTO:
The remaining battery capacity is shown as a percentage,
except that when this is impossible the battery voltage appears.
VOLT:
The battery voltage is shown.
3
Turn the MENU knob to move the
b
mark to the item
you want to set, and press the MENU knob.
The
b
mark on the left of the selected item changes to
a
z
mark, and the
z
mark on the left of the setting
changes to a ? mark.
4
Turn the MENU knob to select whether the selected
item should appear in the viewfinder display (the
“ON” setting), or not appear (the “OFF” setting), and
press the MENU knob.
The
z
mark returns to a
b
mark, and the ? mark
returns to a
z
mark.
Note that pressing the CANCEL/PRST / ESCAPE
switch to CANCEL/PRST on this page has no effect.
5
To set another item to “ON” or “OFF,” repeat steps
3
and
4
.
6
To end the menu operation, set the MENU ON/OFF
switch to OFF or close the cover of the menu operating
section.
The menu disappears from the viewfinder screen, and
the display indicating the current status of the
camcorder appears along the top and bottom of the
screen.
5-2-3 Display Modes and Setting
Change Confirmation/Adjustment
Progress Messages
You can limit or suppress the messages that give details of
setting changes and adjustment progress and results by
setting a display mode.
The conditions under which messages are displayed and
their correspondence with the display mode are as follows:
1) This is also displayed for about 3 seconds when the SHUTTER selector is
set to ON.
“4-1 Adjusting the Black Balance and the White Balance”
Changing the display mode
The currently set display mode appears on the VF DISP 1
page of the USER menu. To change it, proceed as follows:
1
Follow steps
1
and
2
in
, until the VF DISP 1 page of the
USER menu appears on the screen.
Item
Description
DISP ZOOM
Zoom position indicator
DISP COLOR TEMP. Displays the color temperature.
DISP BATT
REMAIN
1)
Displays the battery voltage/
remaining capacity of an internal
battery pack or an external
battery connected to the DC IN
connector.
DISP DC IN
Displayed when the power is
supplied from an external
battery connected to the DC IN
connector.
DISP 16:9/4:3 ID
Displays the 16:9/4:3 mode
indicator.
DISP WRR RF LVL
Displays the reception level of
the wireless microphone.
DISP E. MARK IND
Displayed when an essence
mark has been recorded.
DISP TIME CODE
Displays the time code.
DISP VIDEO RATE
Displays the recording video
signal rate.
Setting change confirmation/adjustment progress messages
and display modes
Y: Message is displayed.
N: Message is not displayed.
Message
display
condition
Message
Display
mode setting
1
2
3
When the filter
selection has
been changed
ND : n, CC : m
(where n = 1, 2, 3, 4,
m = A, B, C, D)
N
N
Y
When the gain
setting has been
changed
GAIN : n (where n =
–3 dB, 0 dB, 3 dB, 6 dB,
9 dB,12 dB, 18 dB, 24 dB,
30 dB, 36 dB, 42 dB,
48 dB)
N
N
Y
When the
setting of the
WHITE BAL
switch has been
changed
WHITE : n
(where n = A CH, B CH,
PRESET)
or ATW : RUN
N
N
Y
When the
OUTPUT/DCC
selector has
been set to DCC
ON or OFF
DCC : ON (or OFF)
N
Y
Y
When the
shutter speed
and mode
setting has been
changed
1)
SS : 1/100 (MSW-970) or
1/60 (MSW-970P)
(or 1/125, 1/250, 1/500,
1/1000, 1/2000, ECS,
SLS)
N
Y
Y
When the black
or white balance
has been
adjusted
2)
E.g. AWB : OK
N
Y
Y
Summary of Contents for MSV-970
Page 5: ...5 ...
Page 168: ...168 Index Index ...
Page 170: ...Sony Corporation MSW 970 970P SY 3 863 920 03 1 Printed in Japan 2006 11 13 2005 ...