93
Adjustments and Settings from Menus
Chap
te
r 5
Men
u
Dis
p
la
ys
a
nd Det
a
iled
S
e
ttin
gs
3
Turn the MENU knob to move the
b
mark to the item
you want to set, and press MENU knob.
The
b
mark on the left of the selected item changes to
a
z
mark, and the
z
mark on the left of the setting
changes to a ? mark.
4
Turn the MENU knob to change the setting, and press
the MENU knob.
The
z
mark on the left of the selected item returns to
a
b
mark, and the ? mark on the left of the setting
returns to a
z
mark.
Any of –3, 0, 3, 6, 9, 12, 18, 24, 30, 36, 42 or 48 dB
can be set for each of the L, M, and H positions, in any
sequence.
For TURBO, any of –3, 0, 3, 6, 9, 12, 18, 24, 30, 36,
42 or 48 dB can be selected.
To change the gain corresponding to another switch
position, return to step
3
.
5
To end the menu operation, set the MENU ON/OFF
switch to OFF or close the cover of the menu operating
section.
The menu display disappears, and the current status of
the camcorder is shown along the top and bottom of
the viewfinder screen.
5-3-2 Selecting the Output Signals
When the optional CBK-SD01 extension board is
installed, you can select the type of video signals (VBS/
SDI) from the VIDEO OUT SEL connector on the
OUTPUT SEL page of the USER menu.
Proceed as follows:
1
Set the MENU ON/OFF switch to ON.
The last accessed menu page appears on the
viewfinder screen.
2
Turn the MENU knob until the OUTPUT SEL page
appears, then press the MENU knob to select the page.
OUTPUT SEL page
3
Turn the MENU knob to move the
b
mark to “REAR
BNC OUT SEL,” and press the MENU knob.
The
b
mark on the left of “REAR BNC OUT SEL”
changes to a
z
mark, and the
z
mark on the left of the
setting changes to a ? mark.
4
Turn the MENU knob to change the desired setting,
and press the MENU knob.
The
z
mark returns to a
b
mark, and the ? mark on the
left of the setting returns to a
z
mark.
5
To end the menu operation, set the MENU ON/OFF
switch to OFF or close the cover of the menu operating
section.
5-3-3 Setting the Color Temperature
Manually
You can adjust the value of the white balance manually by
setting the color temperature.
Proceed as follows:
1
Holding down the MENU knob, move the MENU ON/
OFF switch to ON.
The TOP menu appears.
2
Turn the MENU knob to move the
b
mark to “PAINT,”
and press the MENU knob.
TURBO SW IND OFF: When you operate the GAIN
selector after pressing the TURBO
GAIN button once, the video gain is
changed according to the GAIN
selector operation.
ON: When the video gain is boosted
to the video gain to the value preset
by pressing the TURBO GAIN
button once, the video gain is not
changed even if you operate the
GAIN selector, until you press the
TURBO GAIN button once more.
Item
Description
Item
Description
REAR BNC OUT
SEL
Selects the type of the video signal to
be output from the VIDEO OUT
connector.
SDI: Outputs the SDI signal. When SDI
is selected, connect the VIDEO OUT
connector to the SDI IN connector of
the video monitor.
VBS: Outputs the analog composite
video signal. When VBS is selected,
connector the VIDEO OUT connector
to the VIDEO IN connector of the
video monitor.
U01 OUTPUT SEL
REAR BNC OUT SEL: VBS
Summary of Contents for MSV-970
Page 5: ...5 ...
Page 168: ...168 Index Index ...
Page 170: ...Sony Corporation MSW 970 970P SY 3 863 920 03 1 Printed in Japan 2006 11 13 2005 ...
