USO
RESTRITO
258
Multi Program 2
Ch
a
p
te
r 10
S
p
e
c
ia
l Fun
c
ti
o
n
s
of the Engineering Setup >Router/Tally >Router menu,
select other than [128 × 128].
For details, see “Assigning Switcher Inputs and Outputs to
S-Bus Space” in Chapter 23 (Volume 2).
As for the bus number of the utility 3 bus, a DME Key bus
number is used as follows.
No.
Bus (Standard)
Bus (MP2)
70
M/E-1 DME Key
M/E-1 Utility3
85
M/E-2 DME Key
M/E-2 Utility3
100
M/E-3 DME Key
M/E-3 Utility3
115
P/P DME Key
P/P Utility3
Making settings for timeline-related
keyframe operations
To assign sub regions to the region selection
buttons in the numeric keypad control block
In the Engineering Setup >Panel >Config >10 Key Region
Assign menu, assign regions to the region selection
buttons in the numeric keypad control block.
For details, see “Overall Control Panel Settings (Config
Menu)” in Chapter 19 (Volume 2).
To make region and reference region selections
using a menu
During snapshot or keyframe operations, you can select a
region (including sub) in the Key Frame >Region Select
menu. This is convenient for selecting some of the regions
assigned to the numeric keypad control block or changing
the reference region.
For details, see “Specifying the Region and Edit Points”
in Chapter 13 (Volume 2).
To assign regions shown in the Timeline menu
You can select how regions assigned to region selection
buttons appear in the Key Frame >Time Line menu.
For details, see “Settings in the Timeline Menu” in
Chapter 13 (Volume 2).
Enabling reentry between the main and
sub sides of the same M/E bank
In the Engineering Setup >Switcher >Config menu, set
[MP2 Free Re-Entry] to On.
Notes
•
Reentry adds a 1H delay to the video. Nested reentry
may lead to problems in the video.
•
A maximum of ten reentry stages are possible, with the
final output having a delay of 5H.
•
The selection order of reentry signals affects the number
of lines by which the output signal is lowered.
•
If a delay occurs in the image, even when the through
mode is set, the ancillary data does not pass through.
•
For example, it is possible to select the reentry of M/E-1
main on M/E-1 main.
Restrictions on mutual reentry when using Multi
Program 2
The snapshot function is affected by this reentry function.
When [MP2 Free Re-Entry] is On, and any of the switcher
banks are in Multi Program 2 mode, then the following
restrictions apply.
If you save and recall snapshots simultaneously with more
than one region specified, the recorded state is played back
in the order of precedence of regions (M/E-1 >M/E-2 >M/
E-3 >M/E-4 >M/E-5 >P/P). Therefore, if you save and
recall snapshots with more than one region specified, the
cross-point settings may not be recalled correctly.
To recall the snapshots correctly, press the cross-point
button before recalling the snapshots, to select a signal
other than the reentry signal, then recall the snapshots.
Functions Added in Multi Program 2
Mode
•
You can set video processing for the utility 3 bus signal.
•
In the control panel and DCU GPI input settings and
switcher GPI link settings, the actions that can be
selected now also include “Sub Cut” and “Sub Auto
Trans.”
•
A switcher GPI link can now be set also for the utility 3
bus.
•
To the macro event configuration parameters and macro
attachment settings, “Main & Sub” and “Sub” have been
added.
•
For cross-point button link settings, M/E-1 to M/E-5,
and P/P “Sub Program,” “Sub Preset,” and “Sub Trans
PGM” have been added to the link source bus.
•
Snapshot attributes can now be set independently for
main and sub.
•
There are additional menus for sub which can be recalled
by pressing a button twice.
•
You can set [MP2 Auto Correct] to On or Off in the
Effect menu or Snapshot menu. When this is set to On,
for example, copy destination and source data is
automatically recognized as main or sub, and the data
interchanged.
•
When the key adjustment mode is selected on the
Multifunction Flexi Pad control block (or when the
[KEY ADJ] button is lit), if you select the region
selection button to which [M/E-x Sub] is assigned, the
[TRNS] button operates as a button for the sub region.
•
You can assign [SUB TRANS] to the key control block.
This button functions as a [TRNS] button for the sub
region.
Summary of Contents for MVS-8000X SystemMVS-7000X System
