153
Maintenance Menu
Chap
te
r 7
Men
u
s
To change a menu item setting
Carry out the following operations to change the setting.
For information about how to change network settings see
next section “To change network settings”.
1
Use the PUSH SET(S.SEL) knob or the
V
/MARK1
and
v
/MARK2 buttons to select the required item,
then press the PUSH SET(S.SEL) knob or the
SELECT function button (F2).
The sub-items of the selected item appears.
2
Select a sub-item with the same operation as step
1
,
and use the PUSH SET(S.SEL) knob or the
V
/MARK1
and
v
/MARK2 buttons to change the setting.
3
Press the PUSH SET(S.SEL) knob or the SELECT
function button (F2) to confirm the setting change.
4
Press the SAVE function button (F5).
The message “NOW SAVING...” appears on the video
monitor display, and “Saving...” appears in the time
data display area, while the new settings are saved in
memory. When the saving operation is completed, the
video monitor display and the time data display area
return to their normal indications.
To cancel changing a setting
Before pressing the SAVE function button (F5), press the
MENU button.
The menu disappears from the video monitor display,
without saving the new setting.
To change network settings
To change network settings, carry out the procedure
described in the previous section, “To display the
maintenance menu”, to display the NETWORK menu
item, then carry out the following operations.
For details of the settings, consult your network
administrator.
When the IP address is assigned automatically
Check that the network cable is connected to this unit
before carrying out the operation.
Follow the procedure as shown in previous section “To
change a menu item setting” to set maintenance menu item
M5: NETWORK >M50: DHCP to “ENABLE”.
To check the assigned IP address
Select maintenance menu item M5: NETWORK
>M51: IP ADDRESS PRESET.
If the IP address cannot be assigned, this is shown as
“000.000.000.000.” In this case, consult the network
administrator.
To set the IP address
First set DHCP to “DISABLE”
(see the previous section,
“When the IP address is assigned automatically”).
1
Select maintenance menu item M5: NETWORK
>M51: IP ADDRESS PRESET.
2
Press the PUSH SET(S.SEL) knob.
The IP address appears, and the digit that can be
changed flashes.
3
Set the IP address.
To select a different digit to be changed
Use the
B
/IN and
b
/OUT buttons.
To change the value of a digit
Turn the PUSH SET(S.SEL) knob.
Turning clockwise increases the value, and turning
counterclockwise decreases the value.
The
V
/MARK1 and
v
/MARK2 buttons can be used.
Character string at the
right of a menu item
Current setting of the menu item
When shown with a colon (:):
the
current setting is the same as
the factory default setting.
When shown with a raised dot
(.):
the current setting is
different from the factory
default setting.
An
*
(asterisk) in a
complete list of settings
Factory default setting
On-screen indication
Meaning
REC
NET
REMOTE
LOCAL
VARIABLE KEY INHI
PRE-
SET
ON
OFF
PB
PHONES
LEVEL
SHIFT
DISPLAY
HOME
PAGE
EXPAND
CHAPTER
TOP
F REV
F FWD
END
STANDBY
REC INHI
PREV
NEXT
PLAY
STOP
REC
THUMBNAIL
RETURN
PUSH SET(S.SEL)
MENU
RESET
MARK2
MARK1
IN
OUT
SHTL/JOG
SUB CLIP
DISC MENU
VAR/JOG
EJECT
ACCESS
CH-1
ALL CH
CH-2
CH-3
CH-4
MENU button
SHIFT button
PAGE/HOME button
Function buttons
Arrow buttons
PUSH SET(S.SEL) knob
Note
Note
