RB1G
CHASSIS
W600A/ W603A/ W605A/ W607A/ W650A/ W651A/ W653A/
W654A/ W655A/ W656A/W657A/ W658A/ W670A/ W674A
Status
White Center LED
Side RGB LED
Side Amber LED
Remarks
Power Off
( by power saving switch
off and *1)
Off
Off
Off
*1 power switch off (by side
key)
Power On
White
Off
Off
Main-micro is in normal
operation
Standby
( by remote control off only
)
Off
Off
Off
Main-micro block is in sleep
mode
Skype Call Receive
white
white blinking
Off
Picture Off
White looping
breathing
one time blinking
Off
Device Connection
White
cyan
Off
Set "On Timer"/ Reminder
/ Set "Rec Timer"
( Power On )
White
Orange
Off
Set "On Timer"/ Reminder
/ Set "Rec Timer"
( Standby )
Off
Off
Orange
Failure
Off
Red
Blinking
Off
The number of LED blinking
indicates cause of failure
( refer to the table of next
page )
Aging mode
white
Green Blinking
Off
Blinking:0.5sec On / 0.5sec
Off
End of Aging mode
White
Green Blinking
Off
Blinking:3sec On / 3sec Off
Software Updating
white blinking
white blinking
off
Software Updating finish
Off
Blue lit
off
Test Reset
White
white blinking
Off
Error of panel ID
Off
Green Blinking
Orange
Blinking
Blinking:0.5sec On / 0.5sec
Off
REC [AEP/J only]
White
Red(Pink) Lit
Off
Picture Frame
White
Orange
Off
ePOP/
Shop Illumination
White
Cyan Lit/
Cyan loop
Off
One shot Center White
when feature change
15
Self Diagnostic Function
2-4. Standby LED Error Display
Note: Details refer to Troubleshooting Section.
2-2. LED Display Control
When safety shutdown occurs, Standby LED display reports the cause by using the lightning
patterns as indicated below
.
2-3. LED Pattern
3.0sec
3.0sec
0.5sec
0.
5sec
Example: The figure above shows LED display when SHUTDOWN is caused by Audio
Error. It repeats flashing for a specified number of times in 0.5sec/cycle and has a 3 seconds
interval of lighting off. Please note that a 3 seconds interval of lighting off is fixed regardless of abnormal state types.
Smart Core RED
LED blinking
count
Detection Items
Board Error Item
Main 19.5V failure [MAIN_POWE]
l
Power Adaptor
* This failure is not saved
l
B* Board Error
Main 5.0/3.3/1.8/1.0/ 1.1V failure [DC_ALERT]
* 5.0/1.0V failures are not saved.
l
B* Board Error
l
Speaker Error
HDMI equalizer/switch I2C NACK [HDMI_EQ]
*There is Temp. sensor on the same I2C bus
l
B* Board Error
Tuner or demodulator I2C NACK [TU_DEMOD]
l
B* Board Error
AFE device I2C NACK [AFE_I2C]
l
B* Board Error
AFE device SPI NACK [AFE_SPI]
(only for AEP,CH,HK)
l
B* Board Error
l
LED Driver Error
l
Panel Module
T Con Error [TCON_ERR]
(MD/MW/HG/TE
Model)
l
Tcon Board
l
Panel
module
l
Tcon
board
l
G*
Board Error
l
B* Board Error
6x
LED driver [BACKLITE]
l
LED Driver (LD) Board Error
Over temperature protection [TEMP_ERR]
*Temp. sensor I2C NACK [TEMP_ERR] *There
is HDMI Eq on the same I2C bus.
8x
Software Error (VPS/MEPS/HOST/STBY/AFE
WDT)
l
B* Board Error
2x
3x
l
B* Board Error
Audio amp. protection [AUD_PROT]
Panel ID EEPROM I2C NACK (Also panel
power failure is a suspect) [P_ID_ERR]
7x
l
B* Board Error
LED Driver Error [LD_ERR]
(HG/TE Model)
4x
5x
Note:
G BOARD : ( N/A FOR THIS MODEL)
RB1G
CHASSIS
W600A/ W603A/ W605A/ W607A/ W650A/ W651A/ W653A/
W654A/ W655A/ W656A/W657A/ W658A/ W670A/ W674A
Size
B* Board Type
(Segment: LW)
OTHERS
EUROPE
JP
24”
BLX
BLE
BLJ
32”
BKX/
BLX
BKE/
BLE
BKJ/
BLJ
42”
BKX/
BLX
BKE/
BLE
BKJ/
BLJ
50”
BLX
BLE
-