Backing up the Remote Commander's settings on your PC
You can send (upload) the RM-AX4000 Remote Commander settings (raw -data) to your PC to make a backup copy.
You can use the raw -data by sending (dow nloading) it to the Remote Commander in case of trouble.
Note
You cannot edit the raw -data (saved onto your PC) on AX Remote Editor.
Uploading the settings (raw -data) to your PC for copying
Dow nloading the settings (raw -data) to the Remote Commander
Uploading the settings (raw-data) to your PC for copying
1.
Conne ct the Re m ote Com m ande r (RM -AX4000) to your PC w ith the USB m ini cable .
Note s
o
Do not disconnect the USB mini cable from your PC until uploading is complete, otherw ise a malfunction may occur.
o
Only connect one Remote Commander to your PC at a time. Otherw ise, you w on't be able to upload the settings correctly.
2.
Click "Tools " on the m e nu bar, the n s e le ct "Back up."
The "Backup" dialog box appears.
3.
Click "Back up the raw data on the Re m ote Com m ande r to your PC," the n s e le ct "OK."
The "Save As" dialog box appears.
4.
Se le ct the folde r in w hich you w ant to s ave the s e ttings , the n click "Save ."
AX Remote Editor starts to upload the settings. When uploading is complete, a message box appears.
Note
If "The Remote Commander is not connected or not responding." appears, the Remote Commander (RM-AX4000) may not be connected to your PC
properly. After checking the connection, click "Retry" to repeat the operation.
5.
Click "OK."
The message box closes.
Downloading the settings (raw-data) to the Remote Commander
1.
Conne ct the Re m ote Com m ande r (RM -AX4000) to your PC w ith the USB m ini cable .
Note s
o
Do not disconnect the USB mini cable from your PC until dow nloading is complete, otherw ise a malfunction may occur.
o
Only connect one Remote Commander to your PC at a time. Otherw ise, you w on't be able to dow nload the settings correctly.
2.
Click "Tools " on the m e nu bar, the n s e le ct "Back up."
The "Backup" dialog box appears.
3.
Click "Se nd the raw data s ave d on your PC to the Re m ote Com m ande r.," the n s e le ct "OK."
The "Open" dialog box appears.
4.
Click
of "Look in," the n s e le ct the folde r that contains the s e ttings .
The raw -data file (file extension: .axb) is displayed in the folder in the center of the dialog box.
5.
Se le ct the file you w ant to dow nload, the n click "Se le ct."
The settings (raw -data) dow nload to the Remote Commander starts. When dow nloading is complete, a message dialog box appears.
Note s
o
If the firmw are version of the Remote Commander is older than that of AX Remote Editor, a dialog box appears asking you to confirm updating the
firmw are w hen you click "Select." By clicking "OK," the firmw are is updated.
If you update the firmw are, all the current settings of the Remote Commander are deleted. So proceed w ith caution, being careful not to delete
necessary data.
o
If the version of AX Remote Editor is older than the firmw are version of the Remote Commander, a message box appears asking you to update AX
Remote Editor w hen you click "Select." In this case, after checking the firmw are version of the Remote Commander, dow nload the compatible version
of AX Remote Editor from the w ebsite.
o
If "The Remote Commander is not connected or not responding." appears, the Remote Commander (RM-AX4000) may not be connected to your PC
properly. After checking the connection, click "Retry" to repeat the operation.
6.
Click "OK."
The message box closes.
Page 103
Summary of Contents for RM-AX4000 - Integrated Remote Commander
Page 32: ...Page 32 ...
Page 110: ...Page 110 ...