Sony RM-PP1 Operation Manual Download

Page: 19 / 23

Editing Operation Errors

Error Messages

Error code

Message

Cause

Steps to take

E101

P-REMOTE DISABLE

Player 9-pin status sense data error.
Remote disable detected.

Check the player 9-pin remote control
mode.

E121

R-REMOTE DISABLE

Recorder 9-pin remote disabled.

Check the recorder 9-pin remote control
mode.

E102

P-VTR HARD ERROR

Player VTR hardware error detected.

Check the player VTR state.

E122

R-VTR HARD ERROR

Recorder VTR hardware error detected. Check the recorder VTR state.

E103

REF MISSING

Reference signal connection trouble

Check that reference video signals are
connected to RM-PP1.

E123

R-REF MISSING

Reference signal connection trouble

Check that reference video signals are
connected to recorder VTR.

E104

P-CASSETTE OUT

• Player 9-pin status sense data error.
• Cassette out detected.

Check the cassette in player VTR.

E124

R-CASSETTE OUT

• Recorder 9-pin status sense data

error.

• Cassette out detected.

Check the cassette in recorder VTR.

E105

P-TAPE LENGTH SHORT

• Player 9-pin status sense data

error.

• Invalid cassette type

Check the player VTR and tape length.

E125

R-TAPE LENGTH SHORT

• Recorder 9-pin status sense data

error.

• Invalid cassette type

Check the recorder VTR and tape
length.

E106

P-VTR CNTL T/O

Player 9-pin control time out

Check the player VTR.

E126

R-VTR CNTL T/O

Recorder 9-pin control time out

Check the recorder VTR.

E107

REC INHIBIT

Recorder 9-pin status sense data
error, rec inhibit detected.

Check the REC INHIBIT setting of
recorder VTR and cassette.

E108

PLY DEVICE TYPE ERR

Player VTR device type error

Check the player VTR type.

Note

New VTRs may fail to be recognized in
the device type check.

E128

REC DEVICE TYPE ERR

Recorder VTR device type error

Check to make sure that the recorder
VTR is a play-only device.

Note

New VTRs may fail to be recognized in
the device type check.

E109

P-DF MODE ERROR

Operation error. Different DF mode
between menu setting and timecode
recorded on the cassette in player.

Check the player DF mode setting in
RM-PP1 menu.

E129

R-DF MODE ERROR

Operation error. Different DF mode
between menu setting and timecode
recorded on the cassette in recorder.

Check the recorder DF mode setting in
RM-PP1 menu.

E110

P-SYNC PLAY MISS

• VTR setting error
• VTR error
• 9-pin communications error

• Check the settings for preroll time, edit

delay, etc.

• Check that there is no trouble with the

VTR.

E130

R-SYNC PLAY MISS

• VTR setting error
• VTR error
• 9-pin communications error

• Check the settings for preroll time, edit

delay, etc.

• Check that there is no trouble with the

VTR.

E111

P-CUEUP TIME OUT

• VTR setting error
• VTR error
• 9-pin communications error

Check the player edit point timecode.

Summary of Contents for RM-PP1
























Search results

Summary of Contents for RM-PP1

Reviews:

Related manuals for RM-PP1

Brands by name

Popular brands

Sony RM-PP1, Operation Manual

Search results

Summary of Contents for RM-PP1

Reviews:

Related manuals for RM-PP1

Brands by name

Popular brands