background image

1

2

3

4

7

8

0

9

5

6

PROGR

REC

1-

2-

0

÷

(

p

r

P

)

SAT

TV

AUX

VCR

3-860-405-11(1)

Remote Commander

RM-V20T/V21T

Operating Instructions
Mode d’emploi 

(au verso)

Sony Corporation © 1997  

Printed in Malaysia

English

About This Manual

The instructions in this manual are for RM-V20T and RM-V21T.
Before you start reading, check your model number.  RM-V21T is
the model used for illustration purposes.  Any differences in
operation are clearly indicated in the text,  for example, RM-V21T
only.

Setting Up the Remote Commander

Before you can start using the Remote Commander, you must first
set it up. This manual describes everything you need to know to
set up the Commander, including:
• Installing the batteries
• Presetting the Commander with the codes for your TV, VCR or

satellite tuner (analogue) and another TV, VCR or satellite tuner

About Presetting the Commander

This Remote Commander is preset at the factory to operate Sony
brand TVs (using code No. 01), Sony brand VHS VCRs (using code
No. 03), Sony brand DVs (using code No.04) at AUX position. If
you’re using this Commander with a Sony TV and a Sony VHS
VCR, you won’t need to preset the Commander before you start
using it.
To set up this Remote Commander to use with other (non-Sony)
manufacturer’s TVs, VCRs and satellite tuners, you’ll need to
follow the instructions in this manual to preset the Remote
Commander with the correct code number for your TV, VCR and
satellite tuner.

Note

The Commander can be set up to operate only one component of
each category (VCR, AUX, SAT or TV position of the slide switch)
at a time — unless their code numbers happen to be the same. For
example, you cannot set up the Commander to operate a Sony TV
and a Panasonic TV at the same time (because they use different
code numbers).

Installing the Batteries

Slide open the battery compartment and insert two R6 (size AA)
batteries (not supplied).
Be sure to line up the + and – on the batteries with the + and – on
the battery compartment.

Notes on Batteries

• Under normal conditions, batteries will last up to six months. If

the Remote Commander does not operate properly, the batteries
might be worn out. When replacing batteries, replace both of
them with new ones.

• Do not mix old batteries with new ones or mix different types of

batteries together.

• If you take time to insert the batteries or press the buttons when

replacing the batteries, the code numbers will be erased.

• If the electrolyte inside the battery should leak, wipe the

contaminated area of the battery compartment with a cloth and
replace the old batteries with new ones. To prevent the
electrolyte from leaking, remove the batteries when you plan
not to use the Commander for a long period of time.

Setting the Code

Entering the Code Number

1

Power on the component you want to set
up with its power switch. Then set the
slide switch on the Remote Commander to

VCR

 (to set up a VCR), 

TV

 (to set up a TV)

or 

SAT

 (to set up a satellite tuner).

2

See the supplied “Component Code Numbers” table, and find
the two-character code number for your component.

If more than one code number is listed, use the number that’s
listed first to complete the steps that follow.For example, if
you’re setting up a Philip’s TV, you would use code number

11

.

If your component is not listed, see “Searching for the Correct
Code”.

3

Press and release the 

S

 (Set) button.

4

Enter the component’s code number.
For example, if you’re entering the code
for a Philip’s TV, you would press and
release 

1

, then press and release 

1

.

5

Aim the Remote Commander at the
component and press the 

u

 button.

The component should power off.

6

Press and release the 

 button to store

the code number in the Commander’s
memory.

If the Commander Doesn’t Seem to Be Working...

• First, try repeating these setup procedures using the other codes

listed for your component (see “Component Code Numbers”).

• If — after trying all the codes listed for your component — you

still cannot get the Commander to work properly, try the search
method described under “Searching for the Correct Code”.

If the Commander Seems to Be Working
Properly...

• You’re finished setting up the Commander for this component.
• If you’re setting up more than one component, you’ll need to

complete these procedures for each component you plan to use
with the Commander.

• Use the label (supplied) to write down the code numbers of

your components. Then affix the label to the back of the
Commander.

1

2

Operating a VCR

1

2

3

4

7

8

0

9

5

6

PROGR

REC

1-

2-

0

÷

(

p

r

P

)

SAT

TV

AUX

VCR

RM-V21T

1

To set up the commander.

2

To switch the signals
supplied to the TV.

3

To change the programme.

4

To select double-digit
numbers. Works in the same
way as the VCR’s
commander.

You can use the 

.

 +/– and 

¤

 buttons to operate TV even if the

VCR/AUX/SAT/TV switch is set to VCR.

You can use the 

º

·

r

π

 and 

 buttons to operate

VCR even if the VCR/AUX/SAT/TV switch is set to SAT.

Specifications

Operable distance

Approx. 7 m (23 ft) (varies depending on the component of
each manufacturer)

Power requirements

Two R6 (size AA) batteries (not supplied)

Battery life

Approx. six months (varies depending on frequency of use)

Dimensions

Approx. 64 x 198 x 36 mm (w/h/d) (2 

5

/

8

 x 7 

7

/

8

 x 1 

7

/

16

 in.)

Mass

Approx. 150 g (5.3 oz.) (not including batteries)

Supplied accessory

Label (1)

Design and specifications are subject to change without notice.

RM-V21T

1

To set up the commander.

2

To select double-digit
numbers.  Work in the same
way as the satellite tuner’s
commander.

3

To turn on and off.

4

To change the programme.

5

To select a number between
20 and 29.

6

Programme up:+
Programme down: –

7

To light up the Commander’s
buttons. (The light will
automatically turn off if no
button is pressed for more
than 10 seconds.) (RM-V21T
only)

8

To switch to VCR, AUX,
satellite tuner or TV
operation.

1

2

3

4

7

8

0

9

5

6

PROGR

REC

1-

2-

0

÷

(

p

r

P

)

SAT

TV

AUX

VCR

RM-V21T

1

To set up the commander.

2

To switch to the Teletext.

3

To change the input mode.

SAT

TV

AUX

VCR

#

#

SAT

TV

AUX

VCR

S

Searching for the Correct Code

If you’ve tried all the code numbers listed for your component and
you still cannot get the Commander to work (or if your component
is not listed in this manual), try these steps.

1

Power on the component you want to set
up with its power switch. Then set the
slide switch on the Remote Commander to

VCR

 (to set up a VCR), 

TV

 (to set up a TV)

or 

SAT

 (to set up a satellite tuner).

2

Press and release the 

S

 (Set)

 

button.

3

Press and release the 

PROGR+

 button.

Then press and release the 

u

 button.

4

Repeat step 3 until your component
powers off.
Pressing 

PROGR+

 and 

u

 repeatedly will

try every available code until the correct
one is found. Be patient as you do this; it
may take up to about 80 tries until the
correct code number is located.

5

When the component powers off, press
and release the 

 button to store the code

number in the Commander’s memory.

6

Check that the Commander is operating
the other functions of your component.
Turn on the component again; then press
the programme and volume control
buttons. If the Commander seems to be
working properly, you’re done setting up
the Commander.

If the component does not operate properly, repeat steps 2 to 5
and search another code.  As the searching always start from 01, it
will stop again at the same code as  the last searching.  Pass the
code and continue searching until the next code which the
component turns off.

If you still cannot get the Commander to work properly, see
“Troubleshooting”.

Entering the Code Number for Another TV , VCR or
Satellite tuner

1

Set the slide switch on the Remote
Commander to 

AUX

.

2

Press and release the 

S

 (Set) button.

3

Press and release 

0

 (to set up a VCR),

(

 (to set up a  satellite tuner) or 

)

 (to

set up a TV).

4

Enter the component’s code number in the
same way as after step 4 of “Entering the
Code Number”, or after step 3 of
“Searching for the Correct Code”.

S

PROGR

Using the Remote Commander

Operating a Component

1

Make sure that the slide switch is set to the component you
want to operate.

2

Point the Commander directly at the component.

3

Press the button for the function you want to use.

See “Remote Button Descriptions” for complete descriptions of the
buttons on the Commander.

Using Fastext

With Fastext you can access pages with one key stroke. When a
Fastext page is broadcast, a colour-coded menu will appear at the
bottom of the screen. The colours of this menu correspond to the
red, green, yellow and blue buttons on the Remote Commander.
Press the coloured button which corresponds to the colour-coded
menu. The page will be displayed after some seconds.

Notes on Using the Remote Commander

• Using this Commander will not increase the functions of your

TV, VCR or satellite tuner.  The functions of the Commander are
limited to the functions of the TV, VCR or satellite tuner itself.
For example, if your TV does not have a mute function, the 

¤

button on this Commander will not function with your TV.

• Using the LIGHT function frequently of the Commander will

shorten the battery life.

• Do not remove or tear off the corner protector by force.

Troubleshooting

If you’re having problems setting up or using the Remote
Commander:
• When setting up the Commander, carefully go through the

procedures described under “Setting the Code”. If the code
that’s listed first for your component doesn’t work, try all the
codes for your component — in the order in which they’re
listed. If all the codes fail to work (or if your component is not
listed in this manual), try using the procedures under
“Searching for the Correct Code”.

• Check that you’re aiming the Commander directly at the

component, and that there are no obstructions between the
Commander and the component.

• Make sure the batteries you’re using are not worn out, and that

they’re inserted correctly. Note that whenever you remove the
batteries — to replace them, for example — the code numbers
you’ve set are automatically erased and must be reset.

If you have any questions or problems concerning the Remote
Commander that are not covered in this manual, please call the
telephone number in the warranty.

SAT

TV

AUX

VCR

S

0

(

)

Remote Button Descriptions

Operating a TV

PROGR

Operating a Satellite Tuner

4

To change the programme.
Also to turn on.

5

To select double-digit
numbers. Works in the same
way as the TV’s commander.

6

Fastext button.

7

Volume up: +
Volume down: –

8

To mute volume on TV.
Press again to turn muting
off.

9

To switch to VCR, AUX,
satellite tuner or TV
operation.

To turn off.

To turn on.
To return from Teletext to TV

!™

To select a number between
20 and 29.

Programme up: +
Programme down: –

To light up the Commander's
buttons. (The light will
automatically turn off if no
button is pressed for more
than 10 seconds.) (RM-V21T
only)

5

Rewind

6

Play

7

Record
To record, press 

(

 while

pressing 

r

8

To switch to VCR, AUX,
satellite tuner or TV
operation.

9

To turn on and off.

To select a number between
20 and 29.

Fast forward

!™

Stop

Pause

Programme up: +
Programme down: –

!∞

To light up the Commander’s
buttons. (The light will
automatically turn off if no
button is pressed for more
than 10 seconds.) (RM-V21T
only)

Reviews: