background image

RMT-NWS20

©2016  Sony Corporation    Printed in Malaysia

4-595-639-

11(1)

Remote Commander/

遥控器

Parts and controls

Slide the HOLD switch down to release the HOLD status, and press 
any of the operating buttons (



) to turn on the remote 

commander.

Front side

Back side

HOLD switch

Strap hole

HOLD

Release

Disables the buttons to 
prevent unintentional 
operations.

 

VOL +

  

(Previous) button

 

VOL -

  

(Play/pause) button*

 

Built-in Bluetooth antenna

 

 (Next) button

 

OPR (Operation) lamp

 

Battery compartment lid

 

Lock release button

*   Use the tactile dot on the 

 (Play/pause) button as a guide when 

operating the Remote Commander.

Using Remote Commander

The Remote Commander supports Walkman

 models in the NW-A30 

series and NW-WM1 series. (As of October 2016)
Please check the following website or the catalog for the latest 
information on applicable models.
Since the Remote Commander connects to the Walkman via Bluetooth, 
the battery life of the Walkman may decrease depending on the model. 
Also check the following website for the battery life of the Walkman.

http://www.sony-asia.com/support

 

Ą

How to pair the Remote Commander and the Walkman 
(Bluetooth connection)

You need to pair the Remote Commander and the Walkman when 
using the Remote Commander for the first time, or after replacing the 
battery or resetting the Remote Commander.

Example: Setting the NW-A30 series or NW-WM1 series

Tap 

 - [

 Settings] - [Remote Control Settings] under 

[Bluetooth] to enter the pairing menu.

Tap the Remote Commander setting switch on the Walkman screen 
to set it to [On].

Tap [Add Remote Control].

Press any of the operating buttons (

/VOL+/VOL-/

/

while the search dialog is displayed on the Walkman.
The Remote Commander will power on and pairing will be 
performed between the Remote Commander and the Walkman. 
When pairing is complete, [RMT-NWS20] will be displayed on the 
Walkman.
Tap 

 to return to the previous display. 

 

Ą

How to use the Remote Commander

Press the button corresponding to the operation you would like to 
perform on the Walkman.

 

Ą

How to turn off the Remote Commander

A power button does not exist on the Remote Commander. The Remote 
Commander turns off automatically under the following conditions:

 

– When the Walkman is turned off, the Remote Commander setting 

switch on the Walkman is set to [Off], or pairing information for the 

Remote Commander is deleted from the Walkman

 

– When you do not perform any operations on the Remote 

Commander for about 2 hours

 

– When pairing or connection is not completed within 5 minutes

 

Ą

How to reset the Remote Commander

Reset the Remote Commander in the following situations. As the 
pairing information for the Remote Commander will be deleted from 
the Walkman when you reset the Remote Commander, pair the Remote 
Commander and the Walkman again.

 

– When you want to use the Remote Commander for another 

compatible Walkman

 

– When the Remote Commander is not working properly

 

– When [Not Added] is displayed under [Added Remote Control] after 

you have reset the Walkman or deleted the pairing information for 

the Remote Commander

Simultaneously press and hold the 

 button and VOL - button for 

approximately 10 seconds.

OPR (Operation) lamp indication

OPR (Operation) lamp 
indication

Status of the Remote 
Commander

Blinks twice in blue*.

   

Power on.

Lights up in blue for 2 seconds.

Power off.

Blinks four times in blue*.

           

Resetting of the Remote 

Commander is complete.

Lights up in red continuously 

Not operable due to loss of power.

Blinks in blue and red alternately.

                    

Registration in progress. (Pairing)

Blinks twice in blue* repeatedly.

                      

Connection in progress

Blinks once in blue*.

Button operation after the 

connection is established.

* When the battery level becomes low, the lamp lights up in red.

Using attachments

You can use the attachments to secure the Remote Commander to a 
headphone cable or clip it to your clothes. Use the attachments as is 
convenient for you.

Cable attachment: 
Used to attach the Remote Commander to a headphone cable
Clip attachment: 

 

Used to clip the Remote Commander to clothes, etc.
Note

• Properly secure the attachment to the Remote Commander according to one 

of the following procedures. Otherwise, the Remote Commander may fall off or 
get lost.

Cable attachment

Select either cable attachment A (for a thin cable) or B (for a thick cable) 
based on the thickness of the headphone cable. A or B is indicated on 
the reverse of each cable attachment.

 

Ą

How to set the cable attachment

Instruction Manual/

说明书手册

 

Ą

How to attach to the headphone cable

Note

• You may not be able to use the cable attachment for some headphone cables 

depending on their thickness.

• Do not attach the cable attachment to the branching portion of the headphone 

cable or near the headphone plug. If you attach the cable attachment to one of 
these locations, it may cause the cable to become disconnected.

• Do not wrap the headphone cable around the Remote Commander. Marks may 

be left on the headphone cable.

• The grips may leave marks on the headphone cable.

 

Ą

How to remove the cable attachment

Simultaneously pull up the tab (

) and push the attachment in the 

directions of the arrow (

) to remove the attachment.

Clip attachment

You can use the clip attachment to attach the Remote Commander to 
your breast pocket, etc.

 

Ą

How to set the clip attachment

Release the 
lock switch.

Lock the clip 
attachment.

Note

• Always lock the switch. Otherwise, the Remote Commander may become 

detached and get lost.

• If you attach the clip in a spot where it can easily become detached or is subject 

to external force, the clip may become detached and you may lose the Remote 
Commander.

 

Ą

How to remove the clip attachment

Replacing a battery

When the lamp on the Remote Commander lights up in red, the battery 
is nearly depleted.
Always replace the battery with a new CR1620 lithium battery.

Open the battery compartment lid.

Remove the battery.

Insert a new battery.

Set the battery compartment lid horizontally aligning the tab and 
the concave portion of the Remote Commander (

), then push 

down and slide the lid until it clicks (

).

The battery compartment 
lid will lock.

Confirm that the battery compartment lid has been locked.

Note

• When the battery is removed, the pairing information for the Remote 

Commander is deleted from the Walkman. Pair the Remote Commander and the 
Walkman again.

Precautions

Notes on the Bluetooth function

 

ˎ

Bluetooth wireless technology allows connection at a distance of up 
to about 10 m. However, the effective range may vary depending on 
obstructions (people, metals, walls, etc.) or signal status.

 

ˎ

Because Bluetooth and wireless LAN (IEEE802.11b/g) devices use the 
same frequency (2.4 GHz), signal interference may occur, resulting 
in communication speed decrease, noise, or inability to connect, if 
Bluetooth communications are used near a wireless LAN device. In 
such cases, take the following measures.

 

– Perform Bluetooth communications at least 10 m away from the wireless LAN 

device when connecting your Walkman and a Bluetooth device.

 

– Place your Walkman and the Bluetooth device as close together as possible.

 

– Turn off the wireless LAN device when performing Bluetooth communications 

within about 10 m of a wireless LAN device.

 

ˎ

Radio waves emitted from a Bluetooth device may affect the 
operation of equipment such as electronic medical devices. Turn off 
your Walkman and other Bluetooth devices in the following locations 
as failure to do so may cause an accident.

 

– In hospitals, near priority seats on trains, in airplanes, in places such as 

gasoline stations where flammable gases are present, near automatic doors 
or fire alarms

Notes on handling your Remote Commander

 

ˎ

Keep new and used batteries away from children.

 

ˎ

If the battery compartment does not close securely, stop using the 
product and keep it away from children.

 

ˎ

If you think batteries might have been swallowed or placed inside 
any part of the body, seek immediate medical attention.

 

ˎ

Be sure to follow the precautions below. Failure to do so may cause 
malfunction.

 

– Do not subject the Remote Commander to excessive shock nor drop it.

 

ˎ

Do not place or leave the Remote Commander in the following 
locations.

 

– Locations subject to extremely high temperature, such 

as the hot interior of a car parked in the sun and/or in 
summer

 

– Locations subject to direct sunlight or near a heater 

 

– Locations subject to high humidity, dust, soot or steam

 

– Locations on an unstable surface or in an inclined 

position

 

– Locations subject to vibration

 

– Locations subject to high humidity such as  bathrooms

 

– Locations close to magnetic objects such as magnets, speaker boxes, or TV 

sets

 

ˎ

If your Remote Commander causes interference to radio or television 
reception, turn the Remote Commander off and move it away from 
the radio or television.

 

ˎ

Be sure to follow the precautions below when using your Remote 
Commander. Failure to do so may warp the casing or cause the 
Remote Commander to malfunction.

 

– Do not sit down with your Remote Commander in your 

back pocket.

 

ˎ

Please note that water doesn’t splash, this 
product is not waterproof specification. 
Be sure to follow the precautions below.

 

– Be careful not to drop your Remote Commander into a sink or other container 

filled with water.

 

– Do not use your Remote Commander in humid locations or wet weather such 

as rain or snow.

 

– Do not use your Remote Commander in situations where you will sweat. 

If you touch the Remote Commander with wet hands or put the Remote 
Commander in the pocket of sweaty clothes, the Remote Commander may 
get wet.

 

ˎ

In the event that a foreign object or liquid gets inside the Remote 
Commander, remove the battery immediately and consult your 
nearest Sony dealer or Sony Service Center.

Maintenance

 

ˎ

Do not use solvent such as alcohol, thinner or benzine.

Specifications

Remote Commander

Bluetooth Specifications

•  Communication system: Bluetooth specification version 4.0

•  Output: Bluetooth specification Power Class 2
•  Maximum communication range: Line of sight approx. 10 m  

(30 feet) *

1

•  Frequency band: 2.4 GHz band (2.4000 GHz - 2.4835 GHz)

Power Source

CR1620 Lithium Coin Cell Battery *

2

Operating temperature

5 °C to 35 °C (41 ºF to 95 ºF)

Dimensions (Remote Commander)

w/h/d, projecting parts not included

Approx. 20.8 mm × 74.8 mm × 6.6 mm
(0.82 inches x 2.95 inches x 0.26 inches)

w/h/d

Approx. 20.8 mm × 74.8 mm × 7.9 mm
(0.82 inches x 2.95 inches x 0.32 inches)

Mass (Remote Commander)

Approx. 11 g (0.4 oz)
Battery Life
Approx. 8 months (2 hours usage every day)*

3

*

1

  The range may vary depending on the communication environment.

*

2

  The battery supplied at the time of purchase may have a shorter battery 

life as it is installed at the factory to check the performance.

*

3

  The battery life may differ depending on ambient temperature or the 

status of use. The value is for reference only.

Design and specifications are subject to change without notice.

Troubleshooting

You cannot operate your Walkman by the Remote 

Commander.

 

ˎ

Slide down the HOLD switch on the Remote Commander to release it 
from hold status.

 

ˎ

Check the lamp on the Remote Commander to determine the battery 
level and replace the battery if necessary.

 

ˎ

Reset the Remote Commander to pair the Remote Commander and 
the Walkman again.

 

q

See "Using Remote Commander."

 

ˎ

Restart your Walkman. 

 

q

See the instruction manual of your Walkman.

 

ˎ

A device using the 2.4 GHz frequency, such as a wireless LAN 
device, Bluetooth audio device, or microwave oven, may disturb the 
Bluetooth connection. Use your Walkman and the connected Remote 
Commander away from these devices.

 

ˎ

The Bluetooth connection between your Walkman and the Remote 
Commander may be obstructed by, for example, metal, walls, or 
people. Remove any obstructions or change the location to enable 
proper communications.

You cannot pair the Remote Commander and your Walkman.

 

ˎ

Place the Remote Commander and the Walkman at a distance that 
allows for Bluetooth connections.

Compliance

CAUTION 
Risk of explosion if battery is replaced by an incorrect type. 
Dispose of used batteries according to the instructions.

Trademarks

WALKMAN and WALKMAN logo are registered trademarks of Sony 
Corporation.
The Bluetooth word mark and logos are registered trademarks owned 
by Bluetooth SIG, Inc. and any use of such marks by Sony Corporation 
is under license. Other trademarks and trade names are those of their 
respective owners.

All other trademarks and registered trademarks are trademarks or 
registered trademarks of their respective holders. In this manual, ™ and 
® marks are not specified.

 WARNING: 

Do not ingest battery, Chemical Burn Hazard.

 

ˎ

This product contains a coin cell battery. If the coin cell battery is 
swallowed, it can cause severe internal burns in just 2 hours and can 
lead to death.

 

ˎ

Do not expose the batteries (battery pack or batteries installed) to 
excessive heat such as sunshine, fire or the like for a long time.

 

警告

 

请勿咽下电池,否则可能有化学烧伤的危
险。

 

ˎ

本产品包含一个钮扣电池。如果钮扣电池被
吞下,仅在 2 小时内就会造成严重的内部烧
伤并可能导致死亡。

 

ˎ

请勿将电池(安装的电池组或多个电池)长
时间暴露在直射阳光、火焰或类似的过热热
源附近。

English

Contents

• Remote Commander (1)

• Cable Attachment

• Clip Attachment (1)

(A) (1)

(B) (1)

A battery is already 
set at the factory.

A or B is indicated on the 
reverse of each cable 
attachment.

• Instruction Manual (1) (This manual)

简体中文

使用产品前请仔细阅读本使用说明书,并请妥
善保管

内容

 

ˎ

遥控器(1)

 

ˎ

连接线附件

 

ˎ

线夹附件(1)

(A)

(1)(B)

(1)

出厂时已 
安装电池。

在各连接线附件的
反面标注有A或B。

 

ˎ

说明书手册(1)(本手册)

部件和控制

向下滑动 HOLD 开关释放 HOLD 状态,然后按任
意操作按钮(



)打开遥控器。

前面

后面

HOLD开关

挂绳孔

HOLD

释放

禁用按钮以防
止意外操作。

 VOL +

 

  

(上一个) 

按钮

 VOL -

 

  

(播放 / 暂停)

按钮 *

 

  

内置 Bluetooth 
天线

 

  

(下一个) 

按钮

 

  

OPR(操作) 
指示灯

 电池仓盖

 锁定释放按钮

*  当操作遥控器时,请使用

(播放 / 暂停)

按钮上的触觉点作为指南。

出版年月 :2016/9

Summary of Contents for RMT-NWS20









Reviews: