58
6-1. IC AND FLUORESCENT DISPLAY TUBE CHECK
(SELF-DIAGNOSIS)
The communication between microcomputer and main ICs (self-
diagnosis) and the fluorescent display tube all lit are checked.
Checking Method:
1. After setting the test mode, rotate the
[ AMS ]
dial to
select “92. SET CHECK” and press the
[ AMS ]
dial
to enter.
2. When “SET TEST START” is displayed, rotate the
[ AMS ]
dial clockwise by 1 click to select “0. IC&FL
CHECK?” and press the
[ AMS ]
dial to enter.
3. A checking will start automatically, and “0. IC&FL CHECK”
will be displayed. (Checking time is about 3 seconds)
4. After IC communication check, all segments of fluorescent
display tube will be lit. At this time, check visually for a skipped
character.
5. At successful completion of check, “0. IC CHECK OK” is
displayed. In this case, no error exists in the IC interface. Pro-
ceed to 6-2. AUTO CHECK.
Note:
The check mentioned above tests the communication from micro-
computer to main ICs. Even if the check successfully finished, the
IC to be checked is not always normal. Consider it for reference
only.
6. In case of an IC communication error, the following display
will be given during the checking. Possible causes of error are
as listed below.
Error display
Causes (typical example)
DVD DEC. ERROR
1. IC701 (SACD decoder) is faulty
2. IC701 pin
<znv
(XRST) does not go “H”
• IC901 pin
rf
(XDIS) does not go “H”
• IC902 (expander) is faulty
3. 768fs (33.86688 MHz) is not present to
IC701 pin
<znm
(XTAL)
• IC811 (3-multiplying circuit) is faulty
• Clock signal 256fs is not sent from
AUDIO board (CN901 pin
qg
)
• CN901 pin
qh
(DFGND) and pin
qf
(DF3V) are open or shorted
• CN901 pin
qh
(DFGND) and pin
qf
(DF3V) are open or shorted
• CN901 and FFC connection is loose,
or FFC is disconnected
DVD DRAM ERR
1. IC706 (D-RAM) is faulty
2. IC701 pin
<znv
(XRST) does not go “H”
• IC901 pin
rf
(XDIS) does not go “H”
• IC902 (expander) is faulty
3. Faulty communication line between
IC701 and IC706
• Data line, address line, WE, etc.
4. D903 (1SS367) is faulty
CD DSP ERROR
1. IC509 (CD DSP) is faulty
2. 768fs (33.86688 MHz) is not present to
IC509 pin
ua
(XTAL)
Same as cause 3 of DVD DEC. ERROR
3. IC509 pin
2
(XRST) does not go “H”
• IC901 pin
rf
(XDIS) does not go “H”
• IC902 (expander) is faulty
D/A ERROR
1. IC904 (D/A converter) is faulty
2. Faulty IC703 (jitter amplifier) peripheral
circuits
3. IC901 pin
yf
(JIT) is faulty
EEPROM ERROR
1. IC903 (EEPROM) is faulty
Error display
Causes (typical example)
PRAWN DRAM ERR
1. IC808 (D-RAM) is faulty
*1
2. IC801 (DSD decoder) is faulty
3. 768fs (33.86688 MHz) is not present to
IC801 pin
qf
(MCKI)
Same as cause 3 of DVD DEC. ERROR
4. IC801 pin
qd
(XRST) does not go “H”
• IC901 pin
rf
(XDIS) does not go “H”
• IC902 (expander) is faulty
5. Faulty communication line between
IC801 and IC808
• Data line, address line, WE, etc.
6. D903 (1SS367) is faulty
D+3.3V is not present to IC808
RF AMP ERROR
1. IC001 (RF AMP) is faulty
2. Loose connection between CN503 on
MAIN board and CN001 on RF board,
or FFC disconnection
CN503 pin
ql
(CLK RF), pin
w;
(DATA
RF) and pin
wa
(SDEN) must be checked
SRAM ERROR
1. IC908 (SRAM) is defective.
2. IC907, IC909 (address conversion IC) are
defective.
3. The power voltage (3.3 V) is not supplied
to IC908.
C963 (Dual layer capacitor for backup) is
defective.
Q905 is defective.
4. IC908 pin-20 (XCE) does not go low.
Q901 (digital transistor) is defective.
D902 is defective.
*1 DSD decoder is also checked.
Causes Common to Each IC:
1. Faulty communication line between microcomputer and each
IC.
Disconnected patterns, floating series resistors, bridge, etc.
2. Faulty IC supply voltage.
Particularly, check D+3.3V voltage. (D+5V for display mi-
crocomputer)
3. The power supply voltage for the IC is 3.3V that is generated
by dividing the D5V using the voltage dividing with resistor
network and transistor for SRAM (IC908).
4. Faulty microcomputer communication port to each IC
Note:
In case of more than two errors, the error display is switched over
one after another, thus making the reading difficult.
In such a case, press again the
[ AMS ]
dial to make a
recheck for error reading.
l
L
l
L
l
L
l
L
l
L
Summary of Contents for SCD-C333ES - Super Audio Cd Changer
