4-1
SECTION 4
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
SLV-SE100/SE200/SE250/SE300/SE400/SE450/SX100/SX250
(For printed wiring boards)
•
b
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
• Through hole is omitted.
• Circled numbers refer to waveforms.
• There are few cases that the part printed on diagram
isn’t mounted in this model.
• Chip parts.
(For schematic diagrams)
• All capacitors are in
µ
F unless otherwise noted. pF :
µµ
F.
50V or less are not indicated except for electrolytics and
tantalums.
• Chip resistors are 1/10W unless otherwise noted.
k
Ω
=1000
Ω
, M
Ω
=1000k
Ω
.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum capacitor, Be-
cause it is damaged by the heat.
• Some chip part will be indicated as follows.
Example
C541
L452
22U
10UH
TA A
2520
• Constants of resistors, capacitors, ICs and etc with XX indicate
that they are not used.
In such cases, the unused circuits may be indicated.
• Parts with
★
differ according to the model/destination.
Refer to the mount table for each function.
• All variable and adjustable resistors have characteristic curve B,
unless otherwise noted.
• Signal name
XEDIT
→
EDIT
PB/XREC
→
PB/REC
•
2
: non flammable resistor
•
1
: fusible resistor
•
C
: panel designation
•
: internal component.
•
U
: B+ Line.
•
V
: B– Line.
• Circled numbers refer to waveforms.
• Readings are taken with a color-bar signal input.
• Voltage are dc between ground and measurement points.
• Readings are taken with a digital multimeter (DC10M
Ω
).
• Voltage variations may be noted due to normal production
tolerances.
•
C
: adjustment for repair.
• Circled numbers refer to waveforms.
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)
C
B
E
5
6
4
2
1
3
5
4
6
2
3
1
4
5
2
3
1
1
2
4
5
3
3
2
1
3
2
1
3
2
1
Transistor
Diode
Kinds of capacitor
Temperature characteristics
External dimensions (mm)
When indicating parts by reference
number, please include the board name.
Note :
The components identified by mark
0
or dotted
line with mark
0
are critical for safety.
Replace only with part number specified.
Summary of Contents for SLV-SE100
