– 46 –
•
HAND MAIN BOARD IC603 MB89174LPF-G-289-BND (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Description
1
NC
O
Not used (open)
2
RESET
I
System reset signal input from the reset signal generator (Q615) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
3, 4
MOD0, MOD1
I
Setting terminal for the CPU operational mode Fixed at “L” in this set
5
X0
I
Main system clock input terminal (3.579545 MHz)
6
X1
O
Main system clock output terminal (3.579545 MHz)
7
VCC
—
Power supply terminal (+3V)
8
X0A
I
Sub system clock input terminal Not used (fixed at “L”)
9
X1A
O
Sub system clock output terminal Not used (open)
10
NC
O
Not used (open)
11
TX MUTE
O
Muting control signal output to the IR3N74AN (IC602) “L”: muting on
At TX mode: During sending data to base unit, muting it
12
RX MUTE
O
Muting control signal output to the IR3N74AN (IC602) “L”: muting on
At RX mode: After receiving premble bits from base unit muting it until data sent finished
13
SC
O
Main system power supply (+3V) on/off control signal output “H”: main system power on
14
NC
O
Not used (open)
15, 16
TALK LED
O
LED drive signal output of the TALK/BATT LOW indicator (D607) “L”: LED on
17
KEY LED
O
LED drive signal output of the key back light (D609 to D612) “L”: LED on
18
NC
O
Not used (open)
19
GND
—
Ground terminal
20
NC
O
Not used (open)
21 to 25 ROW5 to ROW1
I
Key scan signal input from the key matrix
26
STPCNT
O
Wakeup control signal output terminal
27
WAKEUP
I
Wakeup input terminal
28
NC
O
Not used (open)
29
BATT OFF
I
Battery level detect signal input from the XC612N3328MR (IC605) “L”: battery off
30 to 34
COL5 to COL1
O
Key scan signal output to the key matrix
35
BATT LOW
I
Battery level detect signal input from the XC612N3328MR (IC605) “L”: battery low level
36
CHG IN
I
Charge detection signal input terminal “H”: charge on
37
CONV
O
Speaker output circuit power supply on/off control signal output
“L”: speaker output circuit power on
38
RING OUT
O
Buzzer sound drive signal output terminal
39
RING VOL
O
Buzzer sound level control signal output terminal “L”: low level, “H”: high level
40
DATA IN
I
Receive data input terminal
41
SQ IN
I
Squelch signal (carrier detection signal) input from the MC3361CDR2 (IC601)
“L”: carrier present, “H”: no carrier
42
TX B
O
TX system power supply on/off control signal output “L”: TX system power on
43
GND
—
Ground terminal
44
DATA OUT
O
Transmit data output terminal
45
DATA EN
O
Transmit data enable signal output terminal
46
PLL CLK
O
PLL serial data transfer clock signal output to the M64884FP (IC502)
47
PLL DATA
O
PLL serial data output to the M64884FP (IC502)
48
PLL EN
O
Chip enable signal output to the M64884FP (IC502)
When PLL EN goes from “L” to “H”, it load data from PLL DATA
Summary of Contents for SPP-933 - 900mhz Cordless Telephone
