3-42
SRW-5000/5500
FMT
SEL
PB CH
CHK
EXIT
[HDCAM SR] [Complete ]
NA : GRN AA1 : GRN AC1 : GRN
NB : GRN AB1 : GRN AD1 : GRN
NC : GRN AE1 : GRN AG1 : GRN
ND : GRN AF1 : GRN AH1 : GRN
NE : GRN AA2 : GRN AC2 : GRN
NF : GRN AB2 : GRN AD2 : GRN
NG : GRN AE2 : GRN AG2 : GRN
NH : GRN AF2 : GRN AH2 : GRN
RF CHECK
REC CH
CHK
AUTO
CHK
FMT
SEL
PB CH
CHK
EXIT
[HDCAM SR] [Complete ]
NA : GRN AA1 : – – – – AC1 : – – – –
NB : – – – – AB1 : – – – – AD1 : – – – –
NC : – – – – AE1 : – – – – AG1 : – – – –
ND : – – – – AF1 : – – – – AH1 : – – – –
NE : – – – – AA2 : – – – – AC2 : – – – –
NF : – – – – AB2 : – – – – AD2 : – – – –
NG : – – – – AE2 : – – – – AG2 : – – – –
NH : – – – – AF2 : – – – – AH2 : – – – –
RF CHECK
REC CH
CHK
AUTO
CHK
DIAG
F1
F2
F3
F4
ALT
F5
F6
F7
F8
F9
F10
DIAG
F1
F2
F3
F4
ALT
F5
F6
F7
F8
F9
F10
To perform the RF checks for all the channels
automatically
To perform the RF check for a selected channel
FMT
SEL
PB CH
CHK
EXIT
Cancel the check ?
[F10] : No
[SFT]
+
[F10] : Yes
RF CHECK
REC CH
CHK
AUTO
CHK
DIAG
F1
F2
F3
F4
ALT
F5
F6
F7
F8
F9
F10
5.
Press the
[SET]
key.
.
The tape runs automatically in PLAY mode to start checking.
To perform the RF checks for all the channels automatically:
.
All the channels are checked in order, and “GRN”, “YEL”, or “RED” is displayed on the right of
each channel. When the checks of all the channels are completed, “Complete” appears.
To perform the RF check for a selected channel:
.
After the check, “GRN”, “YEL”, or “RED” is displayed on the right of the specified channel, and
“Complete” appears.
To cancel the check halfway:
(1) Press the
[F10]
(EXIT) key
The message “Cancel the adjustment ?” is displayed.
(2) Press the
[F10]
(EXIT) key while pressing
[SFT]
(SHIFT) key, and then press the
[F10]
(EXIT) key again to return to the RF CHECK menu.
To continue the adjustment, press the
[F10]
(EXIT) key only.
6.
Confirm the result of the check and eject the alignment tape.
If it is normal, “GRN” is displayed on the right of the channel.
n
If an indication other than “GRN” is displayed on the right of the channel, refer to “For Check
Failure” on the next page.
7.
Press the
[F10]
(EXIT) key to exit the RF CHECK menu.
.
To check another channel or mode in the same format, return to step 2.
.
To perform a check in another format, press the
[F10]
(EXIT) key once to retrun to step 1.
