Sony STR-DA5400ES Service Manual Download

Page: 23 / 218

STR-DA5400ES

SPECIAL MENU MODE
Procedure:

1. Press the [POWER] button to turn on the main power, then while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A.

DIRECT], [MUSIC], [MOVIE] button in order, the message “MENU SPECIALIZED!” appears.

2. Press the [

]/[

] buttons of the remote commander, the message “<<< SPECIAL >>>” appears.

3. Press the [

] button of the remote commander, the item is appears.

4. Each time the [

]/[

] buttons of the remote commander is pressed, the item is switched in order as follows.

Some items can change the content. Display the cursor by pressing the [

] button of the remote commander, and changing the content

by pressing the [

]/[

] buttons of the remote commander, and

x the content by pressing the [

] button of the remote commander

when you want to change the content of the item.

5. To release from this mode, while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A. DIRECT], [MUSIC], [MOVIE] but-

ton in order again, the message “MENU SPECIALIZED OFF” appears.

Items

Display

Remark

SYSTEM version display

SYSTEM VERSION X.XXX

X.XXX: System software version

MAIN Ucom version display

MAIN #####

∗∗∗

vX. XX

#####: Model

∗∗∗

: Destination

X.XX: Main controller software version

Video Ucom version display

Video Ucom Ver X. XX

X.XX: Video system controller software version

FAROUDJA version display

FAROUDJA Ver X. XX

X.XX: Video processor software version (main zone)

FAROUDJA (2nd) version display

FAROUDJA2ND Ver X. XX

X.XX: Video processor software version (2nd zone)

GUI CG-ROM version display

GUI CGROM Ver X. XX

X.XX: CG-ROM software version

DSP Ucom version display

DSP Ucom Ver X. XX

X.XX: DSP controller version

DSP serial

ash version display

DSP SFLASH Ver X. XX

X.XX: Serial

ash software version

DSP parallel

ash version display

DSP PFLASH Ver X. XX

X.XX: DSP parallel

ash version

DSP debug menu

Not used for the servicing

FAROUDJA update

FAROUDJA UPDATE [XXX]

XXX: ON or OFF

HDCP key read

HDCP KEY READ [XXX]

Not used for the servicing

Model/destination change

MODEL [#####

∗∗∗∗

XX]

Not used for the servicing

Video factory menu

Menu mode to enter video calibration menu and DDR access
check menu If the [ENTER] button of the remote commander
is pressed, entering the menu, and operating two the following
menu become possible

Video calibration
(Video factory menu)

V.CALIBRATION START?

Procedure:
1. “DVD” is selected by using [INPUT SELECTOR] dial.
2. Connect a color pattern generator to the COMPONENT

VIDEO ASSIGNABLE (INPUT ONLY) IN2 jack (J6007) on
the A-VIDEO board and DVD VIDEO IN jack (J6003) on the
A-VIDEO board.

3. Input 100% color bars signal from the color pattern generator.
4. Menu that measures individual difference of hardness by

automatic operation in pressing the [ENTER] button of the
remote commander, and corrects reference value. In a mea-
surement once, only one of NTSC/PAL/HD can be measured,
repeat NTSC/PAL/HD calibration from procedure 4.

“Check XXXX V-IN” at display:
Video signal necessary for the measurement while measuring

it last time was not detected and it became an error

Con

rm the input of the video of the terminal connection etc.,

and measure the [ENTER] button of the remote commander
again pressing

DDR access check

DDR CHECK [XX] sec

XX: Time to do access check on DDR (for design evaluation)
(Video factory menu)

Auto cal mic test

SPEAKER OUT [XXXXX]

XXXXX: Selection of speaker output audio [SOURCE]: nomally
mode, [MIC]: mode that output audio from mic from speaker

FL display fonts test

FL FONT [0x

∗∗

= X]

∗∗

: 20 to FE, X: character

FL display test

ALL ON

Each time [DISPLAY] button to change as follows all on

test pattern 1

test pattern 2

all off

all on

Super reset

SUPER RESET [XXX]

Not used for the servicing
If super reset is performed, “up convert signal level adjustment”
will also be initialized
When EEPROM initialization is required, perform the “memory
clearing mode”

RAM watch menu

XXX

Not used for the servicing

www. xiaoyu163. com

QQ 376315150

TEL 13942296513