STR-KS370
2
TABLE OF CONTENTS
SAFETY-RELATED COMPONENT WARNING!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE
WITH MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2 V AC range are suitable. (See
Fig. A)
1.5 k
Ω
0.15
μ
F
AC
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
NOTES ON CHIP COMPONENT REPLACEMENT
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
1.
SERVICING NOTES
.............................................. 3
2. DISASSEMBLY
......................................................... 4
2-1. Disassembly
Flow
........................................................... 4
2-2. Case
................................................................................. 4
2-3. S-AIR
Board
................................................................... 5
2-4. Tuner (FM/AM), IO Board ............................................ 5
2-5. Front Panel Block ........................................................... 6
2-6. MAIN
Board
................................................................... 6
3.
TEST MODE
............................................................. 7
4.
ELECTRICAL CHECK
.......................................... 9
5. DIAGRAMS
................................................................ 10
5-1. Block Diagram - MAIN Section - ................................... 11
5-2. Block Diagram - HDMI PC Section - ............................. 12
5-3. Block Diagram - DSP/S-AIR Section - .......................... 13
5-4. Block Diagram- AMP Section - ...................................... 14
5-5. Block Diagram - SMPS Section - ................................... 15
5-6. Printed
Wiring
Board
- MAIN Board (Component Side) - ................................ 17
5-7. Printed
Wiring
Board
- MAIN Board (Conductor Side) - .................................. 18
5-8. Schematic Diagram - MAIN Board (1/5) - ..................... 19
5-9. Schematic Diagram - MAIN Board (2/5) - ..................... 20
5-10. Schematic Diagram - MAIN Board (3/5) - ..................... 21
5-11. Schematic Diagram - MAIN Board (4/5) - ..................... 22
5-12. Schematic Diagram - MAIN Board (5/5) - ..................... 23
5-13. Printed Wiring Board- S-AIR and IO Board - ................ 24
5-14. Schematic Diagram - S-AIR Board - .............................. 24
5-15. Schematic Diagram - IO Board - .................................... 25
5-16. Printed Wiring Board - HDMI PC Board - ..................... 26
5-17. Schematic Diagram - HDMI PC Board (1/2) - ............... 27
5-18. Schematic Diagram - HDMI PC Board (2/2) - ............... 28
5-19. Printed Wiring Board - DISPLAY, IR, LED,
KEY FUNCTION and KEY POWER Board - .............. 29
5-20. Schematic Diagram - DISPLAY, IR, LED,
KEY FUNCTION and KEY POWER Board - ............... 30
5-21. Printed Wiring Board- SMPS Board - ............................ 31
5-22. Schematic Diagram - SMPS Board - .............................. 32
6.
EXPLODED VIEWS
............................................... 43
6-1. Case, S-AIR Board Section ............................................ 43
6-2. Front Panel Section ......................................................... 44
6-3. Chassis
Section
............................................................... 45
7.
ELECTRICAL PARTS LIST
............................... 46
