Advanced Operation
Advanced Operation
25
Manual Programme
Preset menu*
This menu allows you to tune in analogue channels, one by one.
Further Programme
Preset menu*
This menu allows you to fine tune and set the volume level of an individual analogue
channel.
1.
With the ‘Manual Programme Preset’ option highlighted, press
b
to
display the ‘Manual Programme Preset’ menu.
2.
Press
V
or
v
to select the channel number you wish to manually tune.
Press
b
twice to select the ‘SYS’ column. Press
V
or
v
to select ‘AUS’ for
TV broadcasts or ‘EXT’ for connected equipment. Press
b
to confirm and
select the ‘CH’ column.
3.
Press
V
or
v
to select the required channel tuning (C for terrestrial
channels, S for cable channels or F for direct frequency input). Press
b
to confirm
4.
You now need to tune the channel using one of the following methods:
a) If you do not know the channel number (frequency):
Press
v
to select ‘SEARCH’. The TV automatically searches for the
next available TV broadcast channel or the VCR test signal. When a
channel has been found, press OK to store or
v
to continue
searching.
b) If you know the channel number (frequency):
Use the Numbered buttons to enter the channel number of the
broadcast you want or your VCR channel number. Press OK to
confirm.
c) For connected equipment (EXT):
Press
v
to select ‘AV1’, ‘AV2’, ‘AV3’ or ‘AV4’, depending on which
socket you have connected your equipment to. Press OK to confirm.
5.
Press
B
or
b
to select the ‘LABEL’ column. This option allows you to
assign a name of your choice (up to five letters or number). The name is
displayed briefly on screen when the channel is selected.
Press
V
or
v
until the letter or number you require appears in the display
(select ‘-’ for a blank space). Press
b
to confirm. Repeat this until the
name is complete. Press OK to confirm.
6.
Press
B
or
b
to highlight ‘Skip’. This option allows you to skip unused
analogue channels when selecting channels with the PROG +/- buttons.
(You can still select a skipped channel using the Numbered buttons on
the remote control.)
Press
b
the setting. Press
V
or
v
to select ‘Yes’ or ‘No’. Press OK to
confirm.
1.
With the ‘Further Programme Preset’ option highlighted, press
b
to
display the ‘Further Programme Preset’ menu.
2.
Press
V
or
v
to select the channel number you require. Press
b
repeatedly to highlight one of the following options:
a) VOL (Automatic Volume Offset):
This option allows you to set the volume level for an individual
analogue channel. Press
V
or
v
to adjust the volume level over a
range of -7 to +7. Press OK to confirm.
b) AFT (Automatic Fine tune):
This option allows you to fine tune an analogue channel. Press
V
or
v
to select ‘On’. Alternatively, press
V
or
v
to manually adjust the
tuning frequency over a range of -15 to +15. Press OK to confirm.
The ‘Manual Programme Preset’ menu.
Manual Programme Preset
Select:
Enter:
PROG SKIP
PROG
SYS
CH
LABEL
9
10
11
12
13
14
15
16
17
18
19
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
AUS
AUS
AUS
AUS
AUS
AUS
AUS
AUS
AUS
AUS
AUS
C41
C62
C52
C66
S17
S32
C47
C44
C41
C37
C47
ABC
SEVEN
Nine
Ten
31
SBS
The ‘Further Programme Preset’ menu.
Further Programme Preset
Select:
Enter:
PROG
PROG
VOL
AFT
0
0
0
0
0
0
0
0
0
0
0
On
On
On
On
On
On
On
On
On
On
On
9
10
11
12
13
14
15
16
17
18
19
z
*For analogue channels only (n
ot
available in Digital or AV modes).
