background image

88

n

N

Customizing Your VAIO Computer

Configuring Your Modem

Before you can start using your internal modem (not all modem are built-in), or each time you use your modem while traveling, 
make sure that the country of the active location defined in the 

Phone and Modem Options

 window matches the country 

you are dialing from.

To change your modem country settings

1

Click 

Start

 and 

Control Panel

.

2

Click

 Hardware

 

and Sound

.

3

Click 

Phone and Modem Options

.

The 

Location Information

 window appears.

4

Enter the required information, and then click 

OK

.

The 

Phone and Modem Options

 window appears.

5

Select your location on the 

Dialing Rules

 tab.

6

Click the 

Edit

 button to change the current configuration.

The 

Edit Location

 window appears.

Or
Click the 

New

 button to configure your modem.

The 

New Location

 window appears.

7

Check the country/region settings, and make sure it matches the place you are dialing from.

Pulse dial may not be supported in some counties or areas.

8

If you modified your location settings, click 

Apply

, and then 

OK

.

The 

Phone and Modem Options

 window appears.

Summary of Contents for VGN-NR10E/S





















































































































































Reviews: