Sony VPLL-CT10 Service Manual Download

Page: 21 / 196

1-13

VPL-PS10/PX10/PX15

(GB)

HELP

LAMP/

COVER

TEMP/

FAN

POWER

SAVING

ON/

STANDBY

RESET

APA

VOLUME

ENTER

INPUT

MUTING

PIC

AUDIO

HELP

APA

LASER

INPUT

D KEYSTONE

FREEZE

PJ NETWORK

COMMAND
OFF

VOLUME

ENTER

FUNCTION

RM-PJM15

PROJECTOR

D ZOOM

CLICK

RESET/

ESCAPE

MENU/

TAB

2
3

3 2

I /

INPUT

FREEZE

MENU

ENTER

D KEYSTONE

MS SLIDE

RESET

FUNCTION

D ZOOM

APA

+
–

CLICK

Selecting the Menu Language / Projecting

Press the

key to select LANGUAGE, then

press the

or ENTER key.

Press the

key to select a language, then

press the

or ENTER key.

The menu changes to the selected language.

To clear the menu display

Press the MENU key.
The menu display disappears automatically if no key
is pressed for one minute.

Projecting

Rear remote
control detector

ON/STANDBY
indicator

APA key

for VPL-PX15/PX10

for VPL-PS10

After all equipment is connected completely, plug
the AC power cord into the wall outlet.
The ON/STANDBY indicator lights in red and the
projector goes into the standby mode.

Press the

key to turn on the projector.

The ON/STANDBY indicator lights in green.

Turn on all equipment connected to the projector.
Press the INPUT key to select the input source.

INPUT-A: Selects the video signal input from the

INPUT A connector.

INPUT-B (VPL-PX15 only): Selects display of

the INPUT B (Windows CE) window.

VIDEO: Selects the video signal input from the

VIDEO jack on the video input connectors.

S-VIDEO: Selects the video signal input from the

S VIDEO connector on the video input
connectors.

Turn the zoom ring to adjust the size of the
picture.

Turn the focus ring to adjust the focus.

Note

Looking into the lens when the projector is projecting
an image may cause injury to your eyes.

To cut off the picture

Press the PIC MUTING key on the Remote
Commander (VPL-PX15/PX10 only). To restore the
picture, press the PIC MUTING key again.

To get the clearest picture

You can get the best picture automatically when a
signal from the computer is input. Press the APA key.
The picture is automatically adjusted to project the
clearest picture possible.

(GB)

Notes

• Adjust the signal when a still picture is displayed on

the screen.

• Press the APA key when the full image is displayed

on the screen. If there are black edges around the
image, the APA function will not function properly
and the image may extend beyond the screen.

• If you switch the input signal or re-connect a

computer, press the APA key again to get the
suitable picture.

• “ADJUSTING” appears on the screen. To restore the

original screen, press the APA key again during the
adjustment.

• “Complete!” appears on the screen when the picture

is adjusted properly. However, depending on the
kinds of input signal, the picture may not always be
adjusted properly.

• Adjust the items in the INPUT SETTING menu

when you adjust the picture manually.

For details on the INPUT SETTING menu, see page 29
(GB).

To correct trapezoidal distortion

When the projected image is a trapezoid, correct it by
pressing the D KEYSTONE key on the Remote
Commander or by adjusting DIGIT KEYSTONE in
the INSTALL SETTING menu.

When the base edge is longer than the upper
edge as shown in the figure below:

When the upper edge is longer than the base
edge as shown in the figure below:

For details on “DIGIT KEYSTONE,” see page 33 (GB).

Set the value to negative.

Set the value to positive.

Projecting

To turn off the power

Press the

key.

“Power OFF?” appears on the screen.

Note

The message will disappear if you press any key
except the

key, or if you do not press any

key for five seconds.

Press the

key again.

The ON/STANDBY indicator flashes in green and
the fan continues to run for about 90 seconds to
reduce internal heat build-up. Also, the ON/
STANDBY indicator flashes quickly for the first
60 seconds. During this first 60 seconds, you will
not be able to turn the power back on with the

key.

Unplug the AC power cord from the wall outlet
after the fan stops running and the ON/STANDBY
indicator lights in red.

When you cannot confirm the on-screen
message

When you cannot confirm the on-screen message at
anytime, you can turn off the power by holding the

key for about one second.

Note

Do not unplug the AC power cord while the
fan is still running; otherwise, the fan will
stop even though the internal heat level is
still high. This may lead to a breakdown of the
projector.

Cleaning the air filter

Clean the air filter every 300 hours to ensure
optimal performance.