Sony VPLL-CT10 Service Manual Download

Page: 25 / 196

1-17

VPL-PS10/PX10/PX15

(GB)

The INSTALL SETTING
Menu

The INSTALL SETTING menu is used for changing
the install settings of the projector.

INPUT-B FUNC. is displayed only for the VPL-
PX15.

Operation

1. Select an item

Use the

key to select the item, then press the

or ENTER key.

2. Adjust an item

• When changing the adjustment level:

To increase the value, press the

key.

To decrease the value, press the

key.

Press the ENTER key to restore the original screen.

• When changing the setting:

Press the

key to change the setting.

Press the ENTER or

key to restore the original

screen.

INSTALL SETTING

KEYSTONE MEM: ON

DIGIT KEYSTONE: 0

INSTALLATION:

CEILING-FRONT

MENU POSITION: CENTER

MENU COLOR:

STANDARD

MENU BACKGRND:

STANDARD

INPUT-B FUNC.:

LAMP TIMER: 234H

INPUT-A

STATUS (on-screen display)

Sets up the on-screen display.

ON: Shows all of the on-screen display.
OFF: Turns off the on-screen display except for the

menus, a message when turning off the power,
and warning messages.

For details on the warning messages, see page 40 (GB).

INPUT-A

Selects the computer, component or video GBR (15k
RGB) signal input from the INPUT A connector.

Note

If the setting is not correct, “Please check INPUT-A
setting.” appears on the screen and the color of the
picture becomes strange or the picture is not
displayed.

AUTO INPUT SEL

When set to ON, the projector detects input signals in
the following order: INPUT-A/INPUT-B (VPL-PX15
only)/VIDEO/S-VIDEO. It indicates the input channel
when the power is turned on or the INPUT key is
pressed.

LANGUAGE

Selects the language used in the menu and on-screen
displays.
Available languages are: English, French, German,
Italian, Spanish, Japanese, Chinese, Portuguese and
Korean.

POWER SAVING

When set to ON, the projector goes into the power
saving mode if no signal is input for 10 minutes.

IR RECEIVER

Selects the remote control detectors on the front and
rear of the projector.

FRONT & REAR: Activates both the front and rear

detectors.

FRONT: Activates the front detector only.
REAR: Activates the rear detector only.

The SET SETTING Menu / The INSTALL SETTING Menu

(GB)

KEYSTONE MEM

ON: The DIGIT KEYSTONE setting is stored.

The data is retrieved when the projector power is
turned on. The setting will remain the same every
time.

OFF: The DIGIT KEYSTONE is reset to 0 when the

power is turned on next time.

DIGIT KEYSTONE

Corrects the trapezoidal distortion caused by the
projection angle.
If the base edge of the image is longer, set a negative
value; if the upper edge is longer, set a positive value
to display the image as a rectangle.

INSTALLATION

Set this item to reverse the picture horizontally or
vertically.

FLOOR-FRONT: The picture is not reversed.
CEILING-FRONT: The picture is reversed

horizontally and vertically.

FLOOR-REAR: The picture is reversed

horizontally.

CEILING-REAR: The picture is reversed

vertically.

Note

When using a mirror, be careful of how the
installation is carried out since the picture may be
reversed.

MENU POSITION

Selects the display position of the menu from TOP
LEFT, BOTTOM LEFT, CENTER, TOP RIGHT and
BOTTOM RIGHT.

MENU COLOR

Selects the tone of the menu display from
STANDARD, WARM, COOL, GREEN or GRAY.

MENU BACKGRND

Selects the intensity of the background picture of the
menu display from DARK, STANDARD or LIGHT.

INPUT-B FUNC. (VPL-PX15 only)

Set to ON when using the Windows CE function.

Note

Be sure to exit every application that is open before
you switch the setting from ON to OFF. Otherwise,
the system may crash and you may not be able to
restart the projector.

LAMP TIMER

Indicates how long the lamp has been turned on.

Note

This only displays the time. You cannot alter the
display.

The INSTALL SETTING Menu