2
NW-MS6
TABLE OF CONTENTS
1.
SERVICING NOTES
...............................................
3
2.
GENERAL
...................................................................
4
3.
DISASSEMBLY
3-1. Disassembly Flow ...........................................................
5
3-2. Case Block Assy ..............................................................
5
3-3. Case .................................................................................
6
3-4. Guide (LED) ....................................................................
7
3-5. Chassis (Main) Assy .......................................................
7
3-6. “Console Unit”, “SUB Board”, “MAIN Board” ............
8
3-7. Console Assy ...................................................................
8
3-8. CONSOLE Board ...........................................................
9
4.
TEST MODE
.............................................................. 10
5.
DIAGRAMS
5-1. Block Diagram – MAIN Section – ................................ 15
5-2. Block Diagram
– DISPLAY/POWER SUPPLY Section – ...................... 16
5-3. Note for Printed Wirinig Boards and
Schematic Diagrams ....................................................... 17
5-4. Printed Wiring Boards – MAIN Section – .................... 19
5-5. Schematic Diagram – MAIN Section (1/4) – ................ 20
5-6. Schematic Diagram – MAIN Section (2/4) – ................ 21
5-7. Schematic Diagram – MAIN Section (3/4) – ................ 22
5-8. Schematic Diagram – MAIN Section (4/4) – ................ 23
5-9. Schematic Diagram – SUB Section (1/2) – ................... 24
5-10. Schematic Diagram – SUB Section (2/2) – ................... 25
5-11. Printed Wiring Board – SUB Section – ......................... 26
5-12. IC Pin Function Description ........................................... 31
6.
EXPLODED VIEWS
6-1. General Section ............................................................... 39
6-2. MAIN Board Section ...................................................... 40
7.
ELECTRICAL PARTS LIST
............................... 41
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED
LINE WITH MARK
0
ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C dur-
ing repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 ˚C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 ˚C .
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur
such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
NOTES:
• The recorded music is limited to private use only. Use of the music beyond this limit requires permission
of the copyright holders.
• Sony is not responsible for music files that are not saved on your computer due to unsuccessful recording
from CD or music downloading.
Other features
•Compact size, light weight.
•Skip-proof: you can enjoy uninterrupted enjoyment of music during physical activities such as
jogging or commuting.
•Approximately 4 hours of continuous playback with a rechargeable nickel-cadmium battery.
•Recordable time: up to 30 min., 40 min., 60 min.**, on the supplied 32MB “MagicGate Memory
Stick.”
•Backlight LCD screen: song titles and artist names can be displayed.
•High speed data transfer using the supplied USB cable.
•OpenMG Jukebox software enables you to record compact discs using the ATRAC3 format
(high sound quality, high compression) to the hard drive.
* The copyright protection technology of Network Walkman conforms to the SDMI (Secure Digital Music
Initiative) specifications.
**Differs according to the bit rate when recording. In this case, the figures for the recordable time are when
recording on a 32MB “MagicGate Memory Stick” at 132kbps, 105kbps, and 66kbps.
