XAV-AX200/AX200C2
4
SECTION 1
SERVICING NOTES
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(
Caution:
Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution:
The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to
fl
ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
REPLACING THE LITHIUM BATTERY OF THE REMOTE
COMMANDER (US, CND, E17, AUS, LA, IND only)
Under normal conditions, the battery will last
approximately 1 year. (The service life may be
shorter depending on the conditions of use.)
When the battery becomes weak, the range of the
remote commander becomes shorter.
CAUTION
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or equivalent
type.
Notes on the lithium battery
• Keep the lithium battery out of the reach of children.
Should the battery be swallowed, immediately consult a
doctor.
• Wipe the battery with a dry cloth to ensure good contact.
• Be sure to observe the correct polarity when installing the
battery.
• Do not hold the battery with metallic tweezers, otherwise
a short-circuit may occur.
+ side up
q
IMPORTANT NOTE FOR REPAIRING
This unit might contain individual information that the customer
registered in the replaced old part because it installs the Bluetooth
function.
Therefore, when repairing, because the data that the customer reg-
istered might disappear, get the approval of the customer before-
hand.
If any of the following repair is performed, that data disappears.
• Complete TFT board replacing
• Factory reset (Initialize)
Note:
Replaced old complete TFT board is destroyed with the hammer,
and throw out it.
The SERVICING NOTES contains important information for servicing. Be sure to read this section before repairing the unit.
DESTINATION ABBREVIATIONS
The following abbreviations for model destinations are used in this
service manual.
• Abbreviations
XAV-AX200
AEP :
European area, East European area (Turkey), Middle
East area (Israel) and African area (South Africa) models
AUS : Australian and New Zealand models
CND : Canadian and Latin American area (Puerto Rico) models
E17 :
South East Asian area (Malaysia, Singapore, Thailand)
and East Asian area (Taiwan) models
IND
: Indian model
LA
: Latin American area (Chile, Mexico) model
XAV-AX200C2
LA :
Latin American area (Except for Chile, Mexico, Puerto
Rico) model
MODEL IDENTIFICATION
The XAV-AX200 and XAV-AX200C2 can not be identi
fi
ed by the
model name printed on the front panel top.
Be sure to refer to the model number label af
fi
xed to the bottom
of the main unit.
Model number label
XAV-AX200
or
XAV-AX200C2
XAV-AX200
or
XAV-AX200C2
XAV-AX200
When identifying the destination of the XAV-AX200 or XAV-
AX200C2, refer to the model name, Part No., region code, etc.
of the model number label af
fi
xed to the bottom of the main unit.
XAV-AX200 (IND)
XAV-AX200
4-738-064-0
[]
XAV-AX200 (US, CND)
4-726-465-0
[]
XAV-AX200
XAV-AX200 (AEP, UK, E17)
4-726-467-0
[]
:
XAV-AX200 (E17)
4-726-468-0
[]
:
XAV-AX200 (AEP, UK)
XAV-AX200
AEP, UK
E17
XAV-AX200 (AUS, LA)
XAV-AX200C2 (LA)
4-726-466-0
[]
:
XAV-AX200 (AUS, LA)
4-739-658-0
[]
:
XAV-AX200C2 (LA)
XAV-AX200
or
XAV-AX200C2
XAV-AX200
(AUS, LA)
XAV-AX200C2
(LA)
Ver. 1.1
SYS SET
2018/04/20 05:09:38 (GMT+09:00)
