3
XDR-S3HD
SECTION 1
GENERAL
This section is extracted
from instruction manual.
Tip
The preset can be selected by pressing the number
button of the remote commander. Press
ENTER
after
the preset number is selected.
—Scan tuning
The unit will automatically scan the selected band.
In HD scan, HD Radio stations are scanned.
1
Press
POWER
to turn on the radio.
2
Press
BAND
to select the band AM or FM.
3
Press
MENU
to show the menu display.
4
Turn
TUNE/SELECT
clockwise or
counterclockwise to select “SCAN” or “HD
SCAN,” then press
ENTER
.
Scanning of the selected band starts.
When a station is received, scanning pauses for 3
seconds and then continues.
5
When the unit tunes in to the desired station,
do any of the following operations to stop
scanning.
– Press
ENTER
on the unit or remote commander.
– Press
SCAN
or
HD SCAN
on the remote
commander.
6
If necessary, turn
TUNE/SELECT
clockwise or counterclockwise to tune in to
the station more precisely.
7
Adjust the volume using
VOLUME
.
Tip
You can scan a station directly by pressing
SCAN
or
HD SCAN
on the remote commander.
To listen with the
headphones
You can enjoy the radio and external equipment
connected to the line in by the headphones (not
supplied). Connect the headphones (not supplied) to the
i
(headphone) jack. The speaker is deactivated when
the headphones are connected.
Changing the
display mode and
settings
To change the display mode
Press
DISPLAY
.
The display changes as follows:
When an analog radio station is received
x
A
Field strength level indicator
B
Preset number
*
C
Band
D
Frequency
E
Current time
* When you tune in a station by selecting a preset
number.
When an analog FM broadcast that supports
RBDS (Radio Broadcast Data System) is
received
x
x
x
POWER
VOLUME
TUNE/SELECT
SLEEP
BAND
PRESET
TONE
DISPLAY
MENU
ENTER
RADIO / LINE IN
AM
FM
XM
SIRIUS
SLEEP ALARM
ANTENNA
AM
RESET
LINE IN
FM
SLEEP
ALARM
POWER
1
2
3
4
5
6
7
8
0
9
SCAN
MENU
HD SCAN
BAND
PRESET
TONE
DISPLAY
BRIGHT
VOL
RADIO/
LINE IN
TUNE/
SELECT
ENTER
A
B
AC power cord
The number 5 and the VOL +
buttons have a tactile dot.
Size AAA (R03)
×
2
Preparing the
remote commander
Installing the batteries into the remote
commander (See Fig.
B
)
Insert two size AAA (R03) batteries (not supplied).
When to replace the batteries
With normal use, the batteries should last for about six
months. When the remote commander no longer
operates the unit, replace all the batteries with new ones.
Notes
• Do not charge dry batteries.
• When you are not going to use the remote commander
for a long time, remove the batteries to avoid any
damage caused by leakage and corrosion.
Setting the clock
1
Plug in the unit.
The display will flash “AM 12:00.”
2
Press
MENU
to show the menu display.
3
Turn
TUNE/SELECT
clockwise to select
“TIME SET,” then press
ENTER
.
The hour will start to flash in the display.
4
Turn
TUNE/SELECT
clockwise or
counterclockwise until current hour appears in
the display, then press
ENTER
.
The hour is set and the minutes start to flash.
5
Repeat step 4 to set the minute.
Note
If you do not set the menu within 65 seconds, the setting
mode is canceled.
To change the display to the
daylight saving time
(summer time) indication
1
Press
MENU
to show the menu display.
2
Turn
TUNE/SELECT
clockwise or
counterclockwise to select “DST,” then press
ENTER
.
3
Turn
TUNE/SELECT
counterclockwise to
select “ON,” then press
ENTER
.
“
” appears and the time indication changes to
summer time.
To deactivate the DST function, select “OFF” in step 3.
Playing the radio
—Manual tuning
1
Press
POWER
to turn on the radio.
If “LINE IN” is displayed, press
RADIO/LINE IN
so that the band (AM or FM) appears.
2
Press
BAND
to select the band AM or FM.
3
Turn
TUNE/SELECT
clockwise or
counterclockwise to tune in to a desired
frequency.
A beep sounds when the minimum frequency of
each band is received during tuning.
4
Adjust the volume using
VOLUME
.
Tip
To attenuate the volume, turn
VOLUME
counterclockwise quickly.
Note
The frequency cannot be input with the number buttons
of the remote commander.
—Preset tuning
You can preset 20 stations each for AM and FM.
Presetting a station
1
Follow steps 1 to 3 in “Manual tuning” to
tune the frequency you wish to preset.
2
Press and hold
PRESET
for a few seconds.
You will hear a beep.
3
Turn
TUNE/SELECT
clockwise or
counterclockwise to select the preset number,
then press
ENTER
.
The frequency is stored in the selected preset
number and you will hear a beep.
To preset another station, repeat these steps.
Note
If you try to store another station in the same preset
number, the previously stored station will be replaced.
Tuning in to a station
1
Press
POWER
to turn on the radio.
2
Press
BAND
to select the band AM or FM.
3
Press
PRESET
.
The preset number appears in upper left in the
display.
4
Turn
TUNE/SELECT
clockwise or
counterclockwise to select the preset number.
5
Adjust the volume using
VOLUME
.
