8
XTL-W7000
13
Installation procedure
Mounting example
When installing this unit, be sure to close the monitor of the unit.
If the monitor is opened while installing and given too much
force, it may cause a malfunction.
1
2
3
182
mm
53 m
m
Claws
8
Dashboard
8
9
q;
qs
Fire wall
14
Sony Bus DVD
Master unit
(optional)
Nissan cars
Align the brackets of the factory-installed car stereo with the
mounting holes marked “N” on the side of the TV main unit, and
use the supplied pan-head screws
5
to fasten the brackets.
*
Be sure to use only the supplied pan-head screws
5
for
installation. If any other screws are used, make sure they
conform to the requirements shown below.
Using longer screws can cause internal damage to the unit.
5 mm
6 mm
Damage can also occur if the screws are used directly on the
unit without the brackets of the factory-installed car stereo.
Screws of factory-
installed car stereo
bracket
Bracket of
factory-installed
car stereo
5
Toyota cars (illustration shows an example for a Toyota car)
Align the brackets of the factory-installed car stereo with the
mounting holes marked “T” on the side of the TV main unit, and
use the supplied screws to fasten the brackets. For Toyota cars,
the supplied screws
5
should be used.
Notes
• Do not press the front panel buttons of
the unit during installation and do not
apply strong force.
• Do not place any objects on top of the
unit.
• If a salient of the genuine bracket
touches the unit due to its figure, and
makes attachment hard, process the
bracket by scraping the salient off.
Screws of factory-
installed car stereo
bracket
Bracket of
factory-installed
car stereo
XTL-W7000
XTL-W7000
Sony Bus DVD
Master unit
(optional)
5
15
3
Mounting the TV antenna
Mount the film antenna
qf
to the car and connect the TV main unit.
For directions on connecting the TV main unit, see also “
1
Car Systems Connections (complete
connection diagram)” on pages 8-10.
Before mounting
• It may not be possible to mount the antenna on some cars.
- In cars with glass that does not transmit radio waves
(infrared reflecting glass, insulated glass, glass that is opaque
to electromagnetic waves, etc.), the signal reception will be
extremely poor.
- The antenna cannot be mounted in cars which have airbags
in the front pillars.
• Mount the antenna to the front window, in the specified
location and according to the specified dimensions.
- The supplied film antenna is designed for attaching only to
the front window. If attached to the rear window or
elsewhere in the car, the signal reception may be extremely
poor.
Required items
Have the following items handy before beginning the mounting
procedure.
• Tools (Philips screwdriver, etc.)
• Cellophane tape
• Scissors
• Spray bottle (fill with 500 ml water and one or two drops of
detergent)
• Paper towels
Mounting position
Installation complete
Note
Once you have mounted the film
antenna, do not attempt to remove it and
attach it again, as the adhesive will be
considerably weakened. Be sure to
temporarily fasten the cable and antenna
in place and check that the cable has
sufficient play before permanently
attaching.
Note
• During the mounting procedure, it will
be necessary to remove the front pillar
molding to [attach a ground wire].
When performing the installation
yourself, if you decide it is too difficult
to remove the front pillar molding,
please contact your dealer for
assistance. (Note that your dealer may
charge a fee for their assistance.)
Note
Mount the film antennas to the inside of
the front window. Do not mount the
antennas anywhere other than the
location described here.
Before attaching
Using the supplied cleaning cloth
w;
to
wipe away any oil, wax, or dust tat may
be on the window.
Front pillar
Front pillar
Antenna
input
cable
qg
Film antenna
(left)
qf
TV
Film antenna
(right)
qf
Antenna
input cable
qg
TV antenna
amplifier unit
qd
16
Notes
• The molding on the front pillar will be
fastened in place with clips or screws.
When removing it, take care not to
damage or deform it.
• When performing the installation
yourself, if you decide it is too difficult
to remove the front pillar molding,
please contact your dealer for
assistance. (Note that your dealer may
charge a fee for their assistance.)
Film antenna mounting procedure
1
Check the film antenna
qf
mounting position.
1
Align the film antenna power supply point with the lower
edge of the window’s ceramic line and fasten temporarily
in place with cellophane tape.
Do not remove the adhesive backing from the antenna yet.
The figure below shows the results of this step, for the left
antenna. Temporarily position the right antenna in the
same manner.
2
Mark the left and right sides of the film antenna, using
cellophane tape, etc.
2
Remove the inner molding from the front pillars on
both sides of the front window.
(The above figure shows an example of a car, such as a sedan
or SUV, which as a handle mounted on the front pillar.)
About 120 mm
Power supply point
Ceramic line
Align the
upper edge of
the antenna
with this line.
Temporary fastener
(cellophane tape, etc.)
marking (cellophane tape, etc.)
Front pillar
