Sound Performance Lab Spectralizer 9631 Owner'S Manual Download

Page: 6 / 17

Spectralizer

Connections

Before connecting the S

PECTRALIZER

switch the power off at all

connected units.

The rear panel provides AES/EBU- and S/P-DIF-inputs and

outputs. Any additional channel, status and user-bits are
passed through unaltered, and the outputs can be used at the
same time if required.

The S

PECTRALIZER

operates with 24 bit word width. It accepts

16 bit and 20 bit inputs and will create output signals accor-
ding to the input resolution.

For synchronisation purposes W

ORDCLOCK

and W

ORDCLOCK

HROUGH

BNC connectors are fitted with a switchable 75 Ohm

termination.

MIDI I

and MIDI T

HROUGH

connectors allow presets to be

selected via MIDI program change commands.

For easy upgrade of future software releases, the rear panel

offers RS-232 interface for PC and RS-422 interface for MAC.

Installing Updates:

Note: All presets will be lost after installing a new software version!

Connect your computer with the S

PECTRALIZER

via a serial

port with a standard Z-modem cable.

RS-232 for PC and RS-422 for MAC.

Open a terminal program like “Hyperterminal” on PC
and make the following adjustments:

Baud rate: 9600; Stop bit: 1; Parity: none; Data bit: 8;
Handshake: no; Transfer mode: ZMODEM

Switch on the S

PECTRALIZER

and depress both

RESET

and P

RESET

OWN

until the LC-display says

“wait for Zmodem download“

Load the update file into your terminal program
and send it to the S

PECTRALIZER

. The LC-display

shows the progress of the download in kB.

After successfully installing the new software version the
LC-display says

“download valid”.

Switch the S

PECTRALIZER

off and on. The new

software version number is displayed in the first I

NFO

page (simultaneously depress S

TORE

and A

PPLY

; also

refer to C

ONTROL

LEMENTS

No. 9, I

NFO

If an error occurred during download the LC-display says

“download failed”.

The S

PECTRALIZER

now waits

for a new download. Please check all adjustments on
your terminal program and try again. If you are still
unsuccessful contact your local dealer.

ear P

anel Spectr

aliz

Summary of Contents for Spectralizer 9631


















Search results

Summary of Contents for Spectralizer 9631

Reviews:

Related manuals for Spectralizer 9631

Brands by name

Popular brands

Sound Performance Lab Spectralizer 9631, Owner'S Manual

Search results

Summary of Contents for Spectralizer 9631

Reviews:

Related manuals for Spectralizer 9631

Brands by name

Popular brands