Sound Scourge NV73pq User Manual Download | Manualshive

Page: 10 / 15

background image

10

Wersja-C

BACK PANNEL DESCRIPTION

1

1. AC 230V power outlet.

2. DC power supply outlet for connecting powered device no 1 .

2

3

3. DC power supply outlet for connecting powered device no 2 .

4. Signal ground terminal (CIRCUIT)

4

5

5. Ground terminal (CHASSIS)

6

6. Link.

POWER SUPLY UNIT

Signal ground of the powered device is routed out the power supply through the black terminal
(4) labeled (CIRCUIT). The mass is connected by link (6) with the green terminal (CHASSIS) (5),
which is directly connected to ground. In case of ground loops or hum, the signal ground of the
unit can be disconected by removing the link (6) connecting the two terminal.

«
...
8
9
10
11
12
...
»

Summary of Contents for NV73pq
















Reviews:

No comments

Related manuals for NV73pq

Brand: NAD Pages: 2

Brand: Anthem Pages: 3

Brand: JBL Pages: 13

VIV Six Five Series

Brand: Memphis Pages: 16

Renaissance Signature Mk II

Brand: VAC Pages: 12

Brand: JL Audio Pages: 17

Brand: VINCENT Pages: 64

JAMP-500HC06-SGR

Brand: J&M Corporation Pages: 6

DANTE VIRGIL OB

Brand: Glensound Pages: 26

Brand: Parasound Pages: 11

Brand: Peavey Pages: 4

Brand: M-system Pages: 2

Brand: Crate Pages: 4

Brand: Boss Pages: 16

Brand: McIntosh Pages: 22

Brand: Benchmark Pages: 17

Brand: CTP Systems Pages: 6

Brand: B2 Audio Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands