Sound Scourge NV73pq User Manual Download | Manualshive

Page: 9 / 15

background image

9

POWER SUPLY UNIT

Wersja-C

Power for the NV73pq preamplifier is provided by a dedicated external power supply unit PSU NV73.
The PSU has two output sockets and can power two preamps NV73pq or NV73p.
The PSU's design allows disconnecting signal ground from the ground to eliminate the ground loop
during studio setup.
PSU's chasis is made of the same materials as the NV73pq preamp and harmonizes with its design.
PSU NV73 is sold separately.

«
...
7
8
9
10
11
...
»

Summary of Contents for NV73pq
















Reviews:

No comments

Related manuals for NV73pq

Brand: Xantech Pages: 16

Brand: Xantech Pages: 44

Brand: Xantech Pages: 2

Brand: Xantech Pages: 102

Brand: Xantech Pages: 36

Brand: Camco Pages: 32

Brand: rauland Pages: 10

Le Preamp Series

Brand: Two Notes Pages: 21

Brand: Majorcom: Pages: 8

Brand: Soundavo Pages: 12

Brand: Phoenix Gold Pages: 12

The One Limited Edition Amplifier

Brand: Phoenix Gold Pages: 8

VINGTOR STENTOFON EA1400

Brand: Zenitel Pages: 17

Brand: Carson Pages: 12

Phono Box II USB

Brand: Pro-Ject Audio Systems Pages: 4

Brand: Jedia Pages: 12

CTs 4200 USP/CN

Brand: Crown Pages: 1

Brand: IC Audio Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands