background image

4

SAFETY INSTRUCTIONS

THIS  "WARNING"  SIGN  ALERTS  THE  USER  OF  IMPORTANT  INFO.  NOT  FOLLOWING 

THIS  INSTRUCTIONS  MAY  CAUSE  INJURIES  TO  THE  USER  OR  DAMAGE  TO  THE 

EQUIPMENT.

Warning!

Clean the amplifier periodically with brush or dry cloth to assure the thermal 
efficiency of the heatsink.

This product may reach temperatures over 60°C/140°F. Make sure it is cold 
before touching it;

If you are insecure about the installation of this equipment, get in touch with 
our tech support or with a professional specialized in car audio installation;

Use your sound system safely. The continuous exposure to sound pressures 
over 85dB may cause irreversible hearing damage;

Before  proceeding  with  the  installation  of  any  electric  equipment  on  your 
vehicle, unplug the negative (-) terminal of the battery to avoid  fires, injuries or 
damages;

Do not install the amplifier in places exposed to water, dirt or humidity;

This  equipment  is  for  use  in  automotive  DC  voltage  batteries  between  12.6 
and 14.4 volts. Before installing the equipment, check voltage of the batteries;

Choose a ventilated place to install the amplifier and avoid blocking the side 
ventilation windows;

To  prevent  injuries  to  the  user  or  damage  to  the  amplifier,  read  all  safety 
instructions written on this manual;

Mount the amplifier in a secure way. Avoid mounting it on metallic parts of the 
vehicle, because it may cause ground looping (noise);

Make sure that the location chosen for the amplifier installation does not effect 
the operation of the vehicle;

When  passing  cables  through  metallic  walls,  use  rubber  O-rings  to  avoid 
cable cutting and short-circuits. 

Make sure the cables are properly secured throughout the installation;

Wear gloves, safety glasses and and all necessary PPE during the installation 
of SounDigital amplifiers.

Be careful when making holes in the vehicle. Make sure you are not making 
holes in the fuel tank, brake lines or electrical cables of the vehicle

Summary of Contents for EVOX2 1200.2
















Reviews: