PROGRAMMING ADDITIONAL TRANSMITTERS
SECOND CAR & PADLOCK
Press and HOLD the valet switch, the Park Lights will turn on.
*If connected the Horn will Honk once.
(Repeat from Step 1 if the system does not respond)
Cycle the Ignition Key - ON/OFF ON/OFF ON
(Leaving the key ON)
The system can lean up to 4 different remote’s. Each remote to be used MUST be programmed
together during the same sequence. For security, when a new remote is programmed all
previous remote’s are deleted. Please see remote operation chart for information on using
Second Car / Pad Lock Operations
.
After 5 seconds the park lights will turn off.
*If connected the Horn will Honk 5 times.
Press and release the Lock Button on each of the remote’s to be programmed.
See notes below if the remote is to be programmed for 2nd car or PADLOC.
The system will respond by flashing the park lights for each remote.
*If connected the Horn will Honk once for each remote.
Turn off the key when all the remote’s are programmed.
PADLOC
is used to prevent accidental activation on the remote. The Trunk Button must be
pressed at the same time as the intended feature button. (See Second Car/ PADLOC operation)
Use the same remote programming mode and enter the transmitter’s using the Trunk Button
instead on the Lock Button.
2nd Car Operation
allows a single remote to control two vehicles. Use the same remote
programming mode and enter the transmitter as shown below.
In Car One- Press Lock on both car 1 remote’s. Press Trunk on both car 2 remote’s.
In Car Two- Press Lock on both car 2 remote’s. Press Trunk on both car 1 remote’s.
PROGRAMMING REMOTE’S
ENTERING REMOTE PROGRAM MODE
SYSTEM PROGRAMMING -
Menu 1
PAGE 8
INSTALL MANUAL
TRANSMITTER PROGRAMMING
SYSTEM PROGRAMMING -
Menu 1
PAGE 9
INSTALL MANUAL
PROGRAMMING
RS.2
RS.2
Press Lock
Press Unlock
Press Start
Press #
MENU 1
MENU 2
MENU 3
MENU 4
1 - Cycle the Ignition Key On/Off On/Off On (Leaving the key ON)
2 - Press and release the Program Switch 1 time. The park lights will turn on and the horn
will honk to confirm entering program mode.
3 - Select the Program Menu by pressing...
ENTERING PROGRAM MODE
1 -
Cycle the Ignition Key On/Off On/Off On (
Leaving the key ON
)
2 -
Press and
RELEASE
the Program Switch 1 time and the park light will turn on.
(Horn will honk to confirm program mode has been entered)
3 -
Press and
HOLD
the Program Switch for 5 seconds or until the Park Lights flash 3 times.
4 - Turn the ignition key
OFF
to exit.
(
Confirmed by 3 Park Lights flashes/ Horn Honks)
SYSTEM RESET
The system will confirm the program menu by flashing the park lights and with horn honks.
4 - Press and Release the Program Switch to advance through the settings.
(
Confirmed by Park Lights/ Horn Honks & LED flashes)
5 - Press and Hold the Program Switch to change the setting
.
(
Confirmed by Park Lights/ Horn Honks & LED flashes)
6 -
To exit Program Mode, turn the key off.
(Confirmed by Long Horn Honk)
Example- Programming Menu 1, Setting 3 to Double Lock Pulse.
1 -
Cycle the Ignition Key On/Off On/Off On
2 -
Press and release the Program Switch 1 time. (1 Honk/ Park Lights ON)
3-
Press and release the Lock button for Menu 1. (1 Honk/ 1 flash)
4-
Press and release the program button until the LEDs on the antenna flash 3 times.
**The park lights will flash and the Horn will Honk 3 times to confirm the current setting)
5-
Press and hold the program button. The Park Light will flash once (option 1), pause then flash
twice to confirm option 2 has been selected. The Horn will also Honk 1 time (option 1) then 2
times to confirm the option 2.
6-
Release the program switch and turn off key to exit.
