PROGRAMMING ADDITIONAL TRANSMITTERS
SECOND CAR & PADLOCK
Press and HOLD the valet switch, the Park Lights will turn on.
*If connected the Horn will Honk once.
(Repeat from Step 1 if the system does not respond)
Cycle the Ignition Key - ON/OFF ON/OFF ON
(Leaving the key ON)
The system can lean up to 4 different remote’s. Each remote to be used MUST be programmed
together during the same sequence. For security, when a new remote is programmed all
previous remote’s are deleted. Please see remote operation chart for information on using
Second Car / Pad Lock Operations
.
SYSTEM PROGRAMMING -
Menu 1
PAGE 16
INSTALL MANUAL
TRANSMITTER PROGRAMMING
SYSTEM PROGRAMMING -
Menu 1
PAGE 17
INSTALL MANUAL
DIAGNOSTICS
DIAGNOSTICS CHART
TO ENTER DIAGNOSTIC MEMORY
If the remote starter does not activate when the start button is pressed the park lights will flash a diagnostic
to indicate what shutdown input has been triggered. For example: If the start
button is pressed the park
lights flash 3 times slowly. Looking at the chart below this would indicate that the system is in Service Mode,
simply follow the instructions listed in the owners manual on exiting Service Mode and the remote starter
will begin to function as normal.
PARK LIGHTS STATUS LED
DIAGNOSTIC CODE
3 Slow Flashes LEDs “ON” Solid
System Is In Service Mode
4 Slow Flashes Series of 4 Flashes
N/A
5 Flashes Series of 5 Flashes
Hood Open
5 Slow Flashes Series of 5 Flashes
Ignition On During Start Attempt
6 Flashes Series of 6 Flashes
Brake Pedal Shutdown
7 Flashes Series of 7 Flashes
Tach Lock-Out
8 Flashes
Series of 8 Flashes
3 Start Attempts Without Starting
Step 1-
Turn the ignition ON then OFF. Press and release the Program Button.
Step 2-
The system will respond with three park light flashes and the HORN will HONK the same number of
times as the events in memory.
****Maximum four events, four honks****
NOTE:
If the HORN does not HONK, there are no events in memory.
Step 3-
Press the Program Button once to view the last shut down code. The HORN will HONK once to
confirm code one.
****If the HORN does not HONK, there are no codes in memory.****
Step 4-
The LEDs on the antenna will flash a code corresponding to a shut down trigger. Press the
Program Button again for the second code.
***The HORN will HONK twice to confirm code two three time for code three...***
Step 5-
To
Clear Diagnostic Memory.
While in Diagnostic Mode press and hold the Program Button for
five seconds. The park lights will flash and the Horn will HONK once.
****
Once diagnostic memory has 4 shutdown events in memory, the system will not record any further
shutdown events until the system memory has been cleared.****
LED Flashes Diagnostic
5 Flashes The system was shutdown by the brake switch input
6 Flashes The system was shutdown by the hood pin input
7 Flashes The system did not detect the Tach signal.
8 Flashes The system made 3 start attempts without starting
RS.3
RS.3
After 5 seconds the park lights will turn off.
*If connected the Horn will Honk 5 times.
Press and release the Lock Button on each of the remote’s to be programmed.
See notes below if the remote is to be programmed for 2nd car or PADLOC.
The system will respond by flashing the park lights for each remote.
*If connected the Horn will Honk once for each remote.
Turn off the key when all the remote’s are programmed.
PADLOC
is used to prevent accidental activation on the remote. The Trunk Button must be
Pressed at the same time as the intended feature button. (See Second Car/ PADLOC operation)
Use the same remote programming mode and enter the transmitter’s using the Trunk Button
instead on the Lock Button.
2nd Car Operation
allows a single remote to control two vehicles. Use the same remote
programming mode and enter the transmitter as shown below.
In Car One- Press Lock on both car 1 remote’s. Press Trunk on both car 2 remote’s.
In Car Two- Press Lock on both car 2 remote’s. Press Trunk on both car 1 remote’s.
PROGRAMMING REMOTE’S
ENTERING REMOTE PROGRAM MODE
