background image

WARRANTY & RETURNS

This quality product is warranted by South Bend Lathe Company to the original buyer for one year 

from the date of purchase. This warranty does not apply to consumable parts, or defects due to any 

kind of misuse, abuse, negligence, accidents, repairs, alterations or lack of maintenance. We do not 

reimburse for third party repairs. In no event shall we be liable for death, injuries to persons or 

property, or for incidental, contingent, special or consequential damages arising from the use of our 

products.

We do not warrant or represent that this machine complies with the provisions of any law, act, code, 

regulation, or standard of any domestic or foreign government, industry, or authority. In no event 

shall South Bend’s liability under this warranty exceed the original purchase price paid for this 

machine. Any legal actions brought against South Bend Lathe Company shall be tried in the State of 

Washington, County of Whatcom.

This is the sole written warranty for this machine. Any and all warranties that may be implied by 

law, including any merchantability or fitness, for any purpose, are hereby limited to the duration of 

this warranty. To take advantage of this warranty, contact us by mail or phone to give us the details 

of the problem you are having.

Thank you for your business and continued support.

W A R R A N T Y

Summary of Contents for SB1269

















Reviews: