background image

 

 

Thank you for choosing SOUTH theodolite NT-023.   

Please read the user manual carefully before use. 

 

1.

 

PRECAUTIONS 

a.

 

Do  not  collimate  the  objective  lens  directly  to  the  sunlight 

without a filter. 

b.

 

Do  not  store  the  instrument  in  extremely  high  or  low 

temperature,  to  avoid  the  sudden  or  great  change  of 

temperature.   

c.

 

When  the  instrument  is  not  in  use,  store  it  in  the  case  and 

avoid shock, dust and humidity.   

d.

 

If  there  is  great  difference  between  the  temperature  in  work 

site and that in store place, you should leave the instrument in 

the case till it adapts to the temperature of environment.   

e.

 

If the instrument has not been used for a long time, you should 

remove the battery for separate storage. The battery should be 

charged once a month.   

f.

 

When  transporting  the  instrument  should  be  placed  in  its 

carrying  case,  it  is  recommended  that  cushioned  material 

should be used around the case for support.   

g.

 

For  better  accuracy,  the  instrument  should  be  set  up  on  a 

wooden tripod rather than an aluminum tripod.   

h.

 

Clean  exposed  optical  parts  with  degreased  cotton  or  less 

tissue only! 

i.

 

Clean the instrument surface with a woolen cloth after use. If it 

gets wet, dry it immediately. 

j.

 

Before opening, inspect the power, functions and indications of 

the  instrument  as  well  as  its  initial  setting  and  correction 

Summary of Contents for nt-023





























Reviews: