background image

5

Glass Door Models

•  Some glass door models have support brackets that need to be removed.

Auto-defrost Glass (ADG) Door Models

•  Install condensate evaporator unit on rear of cabinet. Screwdriver is 

required.

•  Auto-defrost models with a condensate evaporator on the back should 

not be placed directly against or touching a wall.

•  Adequate space should be allowed around the exterior walls of the 

merchandisers to allow for evaporation of any condensation that may 

occur on cabinet exterior.

•  Outdoor merchandisers should be located in a shaded area away from 

direct sunlight for the most economical operation.

•  A minimum 115 Volt, 15 Amp grounded power source should be provided 

within a range of the power cord. 

DO NOT USE EXTENSION CORDS.

Electrical

The electrical power supplied to the merchandiser must be as identified on the 

serial number data plate located on the inside of the merchandiser. Electrical 

service connections must be in accordance with the National Electrical 

Code, state code and any local codes that may apply. All merchandisers 

are equipped with a power cord and a 3-prong plug. 

WARNING: Improper 

use or removal of the grounding plug can result in a risk of electric shock! 

Be sure to use a grounded electrical receptacle with a fused circuit sized correctly 

for the electrical load. 

Do not use extension cords. 

Extension cords may decrease 

the voltage to the unit and ultimately cause the compressor or other component 

failure. The merchandiser data plate indicates the recommended maximum over 

current protective device size.
Note: Some outdoor locations require ground fault interrupt (GFI) outlets. These 

outlets may trip upon condensing unit start. Refrigeration equipment is exempt 

in some areas from GFI requirements. Local electric codes should be checked. 

Start Up

Plug merchandiser power cord into lower receptacle of electrical outlet. The 

condensing unit will start immediately (electronically controlled models have a 

delay on startup) and the unit cooler evaporator fans will start on the auto-defrost 

models. The condensing unit will continue to run until air temperature inside the 

BEFORE OPERATION

OPERATION

Summary of Contents for POLAR TEMP 1000AD





























Reviews: