background image

18

1         180814X417  Panel Pnt Control
2         72140512       Bolt, Carriage  5/16-18 UNC x 1-1¦2
3         9266R            Grip, Handle
4         166376           Handle, L.H.
5         73680500       Locknut, Crown  5/16-18
6         19111116       Washer  11/32 x 11/16 x 16 Ga.
7         19121414       Washer  3/8 x 7/8 x 14 Ga.
8         74760516       Bolt, Hex Hd. 5/16-18 x 1
9         74760512       Bolt, Hex Hd 5/16-18 x 3/4
10       10040500       Washer, Lock  5/16
11       73220500       Nut, Hex  5/16-18
12       98000129       Nut, Flanged  5/16-18
13       180847           Bolt, Carriage  5/16-18 x 3/4 Gr. 5

KEY    PART            
NO.     NO.                DESCRIPTION

KEY    PART            
NO.     NO.                DESCRIPTION

14       181452X417  Panel, Handle
16       166377           Handle, R.H.
18       166868           Cable, Control, Tine
19       151229           Lever, Control, Tine
20       154805           Pin, Pivot
21       12000027       Ring, Klip
28       19131312       Washer 13/32 x 13/16 x 12 Ga.
29       12000059       Retaining, Ring
43       180528           Cable Assembly, Reverse
44       181580           Clip
45       73920600       Nut Keps 3/8-24 Unf

NOTE: 

All component dimensions are given in U.S. 
inches.   1 inch = 25.4 mm

REPAIR PARTS

TILLER - - MODEL NUMBER SOF550A

HANDLE ASSEMBLY

For Parts Call K&T 606-678-9623 or 606-561-4983

www.mymowerparts.com

Summary of Contents for SOF550A

























Reviews: