background image

PROBLEM

POSSIBLE CAUSE(S)

SOLLUTION(S)

Engine will not start.

1. Ignition Switch in the “OFF” position.

2. Engine flooded.

3. Fuel Tank empty.

4. Spark Plug not firing.

5. Fuel not reaching carburetor.

6. Carburetor requires adjustment.

1. Move ignition switch to the ON position.

2. See 

Starting a Flooded Engine

 in 

OPERATION

 section.

3. Fill tank with correct fuel mixture.

4. Replace Spark Plug.

5. Check for kinked or split fuel line; repair 

or replace.

6. Contact a qualified service center.

Engine will not accelerate, lacks 

power or stalls.

1. Fuel not reaching carburetor.

2. Air filter dirty.

3. Spark plug fouled.

4. Carburetor requires adjustment.

5. Carbon build-up on muffler outlet 

screen.

6. Compression low.

1. Check for kinked or split fuel line; repair 

or replace.

2. Clean air filter.

3. Clean or replace spark plug

4. Contact a qualified service center.

5. Contact a qualified service center.

6. Contact a qualified service center.

Engine smokes excessively.

1. Fuel mixture incorrect.

2. Air filter dirty.

3. Carburetor requires adjustment.

4. Choke lever in the CHOKE/COLD 

START position.

1. Empty Fuel Tank and refill with correct fuel 

mixture.

2. Clean or replace air filter.

3. Contact a qualified service center.

4. Rotate choke lever to the RUN/WARM 

START position. 

Engine runs hot.

1. Fuel mixture incorrect.

2. Spark Plug incorrect.

3. Carburetor requires adjustment.

4. Carbon build-up on muffler outlet 

screen.

1. See 

Mixing Fuel / 2-Cycle Oil

 in 

OPERATION

 section.

2. Replace with correct Spark Plug.

3.  Contact a qualified service center.

4.  Contact a qualified service center.

Engine will not idle properly.

1. Carburetor requires adjustment.

2. Crankshaft seals worn.

3. Compression low.

1. Contact a qualified service center.

2. Contact a qualified service center.

3. Contact a qualified service center.

Troubleshooting

• Save all instructions 

You may have further questions about assembling, operating, or maintaining this cultivator. If so, you can contact our 

Technical Service Department at 1-800-737-2112 (English only). 

You may also write to:

METL Corporate Office - CORRESPONDENCE ONLY

ATTN: Technical Service – 

METL

6700 Wildlife Way

Long Grove, IL  60047

Technical Service

Questions? Call Toll Free at 1-800-737-2112 

10 

Copyright © 2009 MAT Engine Technologies, LLC

When contacting the Technical Service Department, have 

ready:

• Your Name

• Your Address

• Your Phone Number

• Model Number of Product

• Date of Purchase (include copy of receipt for written requests)

If you need assistance or have any questions, 

CALL TOLL FREE: 1-800–737-2112

Summary of Contents for S-CV-43


















Reviews: