background image

Questions? Call Toll Free at 1-800-737-2112

 

 

Copyright © 2011 MAT Engine Technologies, LLC

21

Warranty

 

(Continued)

• Save all instructions 

This 

MAT Engine Technologies, LLC (METL)

 outdoor power equipment engine complies with the emissions regulations of the United States 

Environmental Protection Agency (“U.S. EPA”) and the State of California.

To the extent there is any conflict between this Emissions Control System Warranty and the equipment manufacturer’s warranty, this 
Emissions Control System Warranty shall apply except where the equipment manufacturer’s warranty may provide a longer warranty 
period. Please read your warranty rights and obligations carefully. Some sections of the warranty may not apply to the specific equipment 
model you purchased. Unless specifically noted otherwise, the terms of the Emission Control System Warranty shall apply to all product 
engines covered within this manual.

The California Air Resources Board, U.S. EPA and 

MAT Engine Technologies, LLC (METL)

 are pleased to explain the Emission Control Sys-

tem Warranty on your new outdoor power equipment engine.

California (applies only to Models SM2010)

In California, new spark-ignited small off-road equipment engines must be designed, built and equipped to meet the State’s stringent 
anti-smog standards.

Other States, U.S. Territories

In other areas of the United States, your engine must be designed, built and equipped to meet the U.S. EPA emission standards for spark-
ignited engines at or below 19 kilowatts.

All of the United States

MAT Engine Technologies, LLC (METL)

 must warrant the emissions control system on your power equipment engine for the periods of time 

listed below provided there has been no abuse, neglect or improper maintenance of your power equipment engine.  Where a warrantable 
condition exists, 

METL

 will repair your power equipment engine at no cost to you including diagnosis, parts and labor.

The emissions control system is warranted for two years. If any emissions-related part on your engine is defective, the part will be repaired 
or replaced by 

METL

.

Owner’s Warranty Responsibility

As the power equipment engine owner, you are responsible for the performance of the required maintenance listed in your owner’s 
manual. 

METL

 recommends that you retain all receipts covering maintenance on your power equipment engine, but 

METL

 can not deny 

warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance.

As the power equipment engine owner, you should however be aware that 

METL

 may deny your warranty coverage if your power equip-

ment engine or a part has failed due to abuse, neglect, improper maintenance or unapproved modifications.

You are responsible for presenting your power equipment engine to a distribution center or service center authorized by 

METL

 as soon as 

the problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should contact 

MAT Engine Technologies, Inc.
6700 Wildlife Way
Long Grove, IL 60047
Tel: 1-800-737-2112

Your Warranty Rightes and Obligations:

Emisson Control System Warranty

B

Manufacturer’s Warranty Coverage:

Summary of Contents for SM2010


























Reviews: